Surprisingly, many of these wire-free models can be used at the gym and even get wet, despite the fact that each earpiece has an exposed charging contact on the inside. Check the IP rating of these; some workout-friendly earphones are only IPX4-rated, so they can stand up to sweat but might be hard to wash. Others are IPX7-rated, which means they can survive getting rinsed and dunked.
If you don’t have time for a detailed breakdown of how codecs work, here’s the abridged version: they determine how data is transmitted from your smartphone to your wireless headphones. Different codecs make different compromises in quality and efficiency. SBC is the lowest common denominator of the Bluetooth codecs. Its support is required by all Bluetooth audio products.
Headphones are available with high or low impedance (typically measured at 1 kHz). Low-impedance headphones are in the range 16 to 32 ohms and high-impedance headphones are about 100-600 ohms. As the impedance of a pair of headphones increases, more voltage (at a given current) is required to drive it, and the loudness of the headphones for a given voltage decreases. In recent years, impedance of newer headphones has generally decreased to accommodate lower voltages available on battery powered CMOS-based portable electronics. This has resulted in headphones that can be more efficiently driven by battery-powered electronics. Consequently, newer amplifiers are based on designs with relatively low output impedance.
At $300 (£279, AU$499), Sennheiser Momentum True Wireless are more expensive than Apple AirPods, Jabra's Elite 65t true wireless earbuds and the Elite Active 65t and Bose SoundSport Free wireless earbuds. But they sound superior to those models, with better bass and cleaner, more detailed audio. They also feature quality performance for making phone calls, with solid noise cancellation, and offer a generally comfortable fit, though they're bigger than the Jabras and stick out of your ear a little more. Their only significant downside is that they gradually lose their charge in the charging case and can end up completely dead after four days or so if you don't recharge the case.
What's most impressive about the EarFun Free is the features: Bluetooth 5.0, both USB-C and wireless charging and fully waterproof (IPX7), according to their specs. Do they sound fantastic? No, but they sound pretty good. They don't have the clarity of higher-end true wireless earbuds that cost $150 or more, but they do have plump bass and enough detail to avoid sounding dull. They're also pretty solid for making calls. An excellent value at less than $45.
An electret driver functions along the same electromechanical means as an electrostatic driver. However the electret driver has a permanent charge built into it, whereas electrostatics have the charge applied to the driver by an external generator. Electret and electrostatic headphones are relatively uncommon. Original electrets were also typically cheaper and lower in technical capability and fidelity than electrostatics. Patent applications from 2009-2013 have been approved that show by using different materials, i.e. a "Fluorinated cyclic olefin electret film", Frequency response chart readings can reach 50 kHz at 100db. When these new improved electrets are combined with a traditional dome headphone driver, headphones can be produced that are recognised by the Japan Audio Society as worthy of joining the Hi Res Audio program. US patents 8,559,660 B2. 7,732,547 B2.7,879,446 B2.7,498,699 B2.
Those who buy either of these headphones are in for a treat. Our reviewer didn’t hold back in their assessment of these cans’ ability to fully realize every detail of a recording, noting their “warm and rigid bass, a midrange that dips close to the ruddy colors of analog tape saturation (without sacrificing an ounce of detail), and a laser tight response up top that helps illuminate vivid clarity and granular instrumental texture across the board.”
The WH-1000xM3’s advanced control systems allow you to let in various levels of ambient sound, with advanced features like voice-only mode, which helps filter through vocal frequencies so you can hear your music and the voices around you while blocking out other sounds. Responsive touch controls let you navigate volume, make calls, and play and pause music with ease, all while helping to maintain a clean aesthetic. Best of all, the WH-1000xM3 offer a staggering 30 hours of battery life, providing even heavy users with days of use from a single charge, and have a quick charge feature that allows you to enjoy five hours of listening after just 15 minutes of charging.
The Jaybird Tarah provides nearly everything the company’s flagship model has to offer but at a much cheaper price point. These IPX7 water-resistant earbuds can withstand full submersion for up to 30 minutes. That said, it’s a matter of durability. You can’t swim and listen to your music at the same time as Bluetooth is far too limited. For that, you’ll need dedicated swimming earbuds with on-board storage.
Electrostatic drivers consist of a thin, electrically charged diaphragm, typically a coated PET film membrane, suspended between two perforated metal plates (electrodes). The electrical sound signal is applied to the electrodes creating an electrical field; depending on the polarity of this field, the diaphragm is drawn towards one of the plates. Air is forced through the perforations; combined with a continuously changing electrical signal driving the membrane, a sound wave is generated. Electrostatic headphones are usually more expensive than moving-coil ones, and are comparatively uncommon. In addition, a special amplifier is required to amplify the signal to deflect the membrane, which often requires electrical potentials in the range of 100 to 1000 volts.
Headphones are available with high or low impedance (typically measured at 1 kHz). Low-impedance headphones are in the range 16 to 32 ohms and high-impedance headphones are about 100-600 ohms. As the impedance of a pair of headphones increases, more voltage (at a given current) is required to drive it, and the loudness of the headphones for a given voltage decreases. In recent years, impedance of newer headphones has generally decreased to accommodate lower voltages available on battery powered CMOS-based portable electronics. This has resulted in headphones that can be more efficiently driven by battery-powered electronics. Consequently, newer amplifiers are based on designs with relatively low output impedance.
We could have gone many ways for this pick, but 1More’s unassuming Triple Drivers just wouldn’t stop popping up into the picture. The 1More in-ear headphones aren’t at the top of the class in performance, but what they do have going for them is unrivaled quality and value at their (very reachable) price point. The company has created plenty of iterations since, including a Quad Driver and even an over-ear version, creatively called the Triple Driver over-ears. But when it comes to value for the money, we always come back to the original wired earbuds.
In-ear headphones are like earbuds but are an upgrade to them. These headphones fit into the wearer's ear canal and stay in place with the use of foam or rubber tips. These tips are available in custom sizes so they can fit each individual wearer. When a proper fit's achieved, in-ear headphones reduce outside noise and deliver sound quality at about the same level as over-ear and on-ear headphones.
×