That amp, if in good working condition, has 100 times the potential sound quality that those 2 headphones can play. You could improve the sound somewhat with a careful EQ, since the Marantz will have power reserve to spare. But I’d try to find a better headphone, and there are some bargains out there. If I were suggesting an ortho, I’d say get the lower price Mad Dog, which will give you great audiophile sound with the Marantz.
In-ear headphones are like earbuds but are an upgrade to them. These headphones fit into the wearer's ear canal and stay in place with the use of foam or rubber tips. These tips are available in custom sizes so they can fit each individual wearer. When a proper fit's achieved, in-ear headphones reduce outside noise and deliver sound quality at about the same level as over-ear and on-ear headphones.
AAC has some advantages when it comes to latency, but we recommend avoiding this if you care about audio quality. We found high levels of noise and lower than average frequency cutoffs—both unacceptable to audiophiles and younger listeners. Though the sound isn’t as bad as some may make it out to be, the shortcomings are noticeable to the human ear at normal listening volumes.
Recently released this summer, the Headphones 700 are the best wireless over-ear headphones that Bose has to over. The combine the best-in-class noise-cancellation with great audio quality. Other than the design overhaul, the biggest difference from the QuietComfort 35 II is that the Headphones 700 have a significantly upgraded microphone array. This allows the headphones to have a wonderful tranparancy mode (or ambient listening mode), and makes maybe the best headphones you can buy for call quality.
The outer shells of in-ear headphones are made up of a variety of materials, such as plastic, aluminum, ceramic and other metal alloys. Because in-ear headphones engage the ear canal, they can be prone to sliding out, and they block out much environmental noise. Lack of sound from the environment can be a problem when sound is a necessary cue for safety or other reasons, as when walking, driving, or riding near or in vehicular traffic.
The iPhone will drive the headphone fine and make a very nice sound, but the amp will make a big improvement in harmonic extension and soundstage. Use the amp whenever possible. Both Headfonia and I concur that the E07k is a great amp, and probably the best thing you can get for up to twice the price. I’m familiar only with the E07k, the E17, and the E12. I think the E07k beats the E17 (and both are also USB DACs), while the E12 is just an amp, and has a darker sound but with more power for inefficient headphones. The Philips is not inefficient.
Time to invest in a new set of headphones? It’s a hugely crowded market with hundreds of models to choose from, so here’s a handy timesaver: The Sony WH-1000xM3 are the best headphones. In fact, their combination of top-notch audio quality, superb noise cancellation, and dependable wireless performance is such a strong formula, we named the WH-1000xM3 the best wireless headphones and the best noise-canceling headphones, too.
What I’m saying here is that it’s better to own three $100 headphones than one $300 headphone. Or three $300 headphones than one $900 headphone. Why? Because most people don’t limit their playlist to strictly one genre. And following the logic from Rule #2, the right headphone-music pairing is going to be better than one expensive headphone paired to the wrong music.
The DT770 is fine – not basshead, the COP is the same size and configuration as the 770, and both of those, large though they are, are “tighter” built so they feel less clunky than the M50. But the biggest problem for you is that the smaller headphones under $200 almost all have a steeply rolled-off treble, which is trouble for the more refined type of music. One possible exception is the Harman Soho.
I already own a few headphones, namely the Audio-Technica ATH-Pro500MK2, ATH-T500, Sennheiser PX 100 II & PX 200 II, and the Philips Downtown and Uptown (Rule #3). I’m thinking of adding a new one and I can’t decide between the Beats Solo 2, Grado SR80e, and Sony MDR-10RC (budget constraints). I listen mostly Pop/Rock and Classical music and I have a cheap (Fiio E06) headphone amplifier.
Dale: There are so many types of amplifiers (and DAC’s with amplifiers) that there is no shortcut for studying all of the options, unless you settle for the most generic approach. Important things to consider are power – if you don’t have enough power for your headphone and the dynamics in the music, clipping will result. Sometimes the clipping is “soft” and not readily noticed, but eventually you would discover that much of the detail goes missing or gets veiled with limited dynamics. Another consideration is whether to use a DAC, which may be a separate DAC or built into the same enclosure as the amp. Most DACs will improve the sound over the DACs that are built into computers, but when a DAC is available to replace the DAC built into most cellphones and low to mid-priced music players, you can usually expect a much greater improvement.
We were frankly surprised at just how good the AirPods Pro turned out to be. The noise cancellation is on-par with Sony’s WH-1000XM3, which is saying a lot. The new in-ear design is both comfortable and secure. And amazingly, they sound way better than Apple’s previous version. We would often bemoan the fact that the AirPods didn’t sound very good, especially when compared to the plethora of decent true wireless options for the same or less money.
However, we also move up to high-resolution audio files, as well as a wide variety of sources, including plugging in directly to a PC or Mac, using USB DACs (digital-to-analog converters), and employing high-quality, dedicated portable players and amplifiers. Finally, we compare the headphones to some of our go-to models, both in their class and price point, as well as a level or two above to find out if they can punch above their weight.
In early powered radios, the headphone was part of the vacuum tube's plate circuit and carried dangerous voltages. It was normally connected directly to the positive high voltage battery terminal, and the other battery terminal was securely grounded. The use of bare electrical connections meant that users could be shocked if they touched the bare headphone connections while adjusting an uncomfortable headset.