The impedance of headphones is of concern because of the output limitations of amplifiers. A modern pair of headphones is driven by an amplifier, with lower impedance headphones presenting a larger load. Amplifiers are not ideal; they also have some output impedance that limits the amount of power they can provide. To ensure an even frequency response, adequate damping factor, and undistorted sound, an amplifier should have an output impedance less than 1/8 that of the headphones it is driving (and ideally, as low as possible). If output impedance is large compared to the impedance of the headphones, significantly higher distortion is present. Therefore, lower impedance headphones tend to be louder and more efficient, but also demand a more capable amplifier. Higher impedance headphones are more tolerant of amplifier limitations, but produce less volume for a given output level.
Expensive: Audiophile-grade headphones can cost anywhere between $130 and $2,000. Headphones in this price bracket are no joke: they create impressive soundscapes, are robust enough for use in a recording studio, and they’re just plain beautiful. If you need a pair of headphones for critical listening, or you simply want the best headphones around, it’ll cost you.
If you’re buying wireless headphones, keep a spare pair of wired headphones around in case the others run out of battery. Wireless headphones are definitely the future, and the convenience is a huge benefit, but they rely on battery power to work their magic, and batteries run out. If you’re going to be in a place where you won’t be able to recharge your wireless headphones, consider keeping a backup wired pair with you so the music never has to stop.
In early powered radios, the headphone was part of the vacuum tube's plate circuit and carried dangerous voltages. It was normally connected directly to the positive high voltage battery terminal, and the other battery terminal was securely grounded. The use of bare electrical connections meant that users could be shocked if they touched the bare headphone connections while adjusting an uncomfortable headset.
Supra-aural headphones or on-ear headphones have pads that press against the ears, rather than around them. They were commonly bundled with personal stereos during the 1980s. This type of headphone generally tends to be smaller and lighter than circumaural headphones, resulting in less attenuation of outside noise. Supra-aural headphones can also lead to discomfort due to the pressure on the ear as compared to circumaural headphones that sit around the ear. Comfort may vary due to the earcup material.
If you have a bass problem you could find a filter of some kind that cuts the low bass. Some bass controls can do that. I haven’t found a music genre that totally lacks strong bass, although “acoustic” sometimes doesn’t have strong bass. Mainly, you should make sure your system is matched properly with amp and headphone, so the different frequencies are in balance. Then you will have better luck with different music.
There’s a lot of debate in the headphone world about wireless audio. Wireless standards like Bluetooth are capable of making music sound great, but because Bluetooth relies on data compression, it will never sound quite as good as a wired connection. The big question is, with the improvements in Bluetooth, can anyone tell the difference anymore between Bluetooth audio and wired audio? We’re skeptical that the difference is meaningful, so here’s our best advice: if you’re an audiophile who cares about hearing music in high fidelity, you’ll probably be better off with a set of wired headphones; if you need everything to sound great but prefer the convenience of wireless connections, go for a pair of Bluetooth headphones.
A planar magnetic driver consists of a relatively large membrane that contains an embedded wire pattern. This membrane is suspended between two sets of permanent, oppositely aligned, magnets. A current passed through the wires embedded in the membrane produces a magnetic field that reacts with the field of the permanent magnets to induce movement in the membrane, which produces sound.
The Bose Frames are non-polarized sunglasses with special speakers built into each arm. The idea is that they’re designed to look like regular sunglasses, but also act as Bluetooth headphones. Since there’s no earbud that actually goes into your ears, the speakers have been engineered to shoot audio down into your ears; the neat thing is that the Bose Frames do a very good job at masking your audio so that the people around you can’t really hear what you’re listening to. They are available in two different frame styles, round (Rondo) or square (Aldo).
Over-ear and on-ear headphones effectively block out outside sounds, allowing you to hear your music or whatever else you're listening to crisply and without distraction. Over-ear headphones are sometimes known as full-size headphones because they completely envelop the wearer's ear. This results in what's known as passive noise reduction, which makes these some of the most-preferred headphones available. The only drawback is that your ears and the skin around your ears can get warm and sweaty. These are usually the heaviest type of headphones.