Headphones are made in a range of different audio reproduction quality capabilities. Headsets designed for telephone use typically cannot reproduce sound with the high fidelity of expensive units designed for music listening by audiophiles. Headphones that use cables typically have either a 1/4 inch (6.35mm) or 1/8 inch (3.5mm) phone jack for plugging the headphones into the audio source. Some stereo earbuds are wireless, using Bluetooth connectivity to transmit the audio signal by radio waves from source devices like cellphones and digital players.[4] Due to the spread of wireless devices in recent years headphones are increasingly used by people in public places such as sidewalks, grocery stores, and public transit. Headphones are also used by people in various professional contexts, such as audio engineers mixing sound for live concerts or sound recordings and DJs, who use headphones to cue up the next song without the audience hearing, aircraft pilots and call center employees. The latter two types of employees use headphones with an integrated microphone.
Interestingly, yesterday I was comparing my beyer 770 with my AT ath30 and then I realised how important it is also the soundstage, the good separation of instruments … finally I have decided I want to take this into account as well, and not only the issue of bass, midrange and treble … Since, in my opinion lack of bass we can try to fix it, but lack of soundstage is impossible, right?

Their combination of dual balanced-armature drivers matched with a dynamic driver to pump up the lower end are kind of engineering normally found on products that cost more than double the price of the 1Mores. Even the smaller details are very well ironed out, such as Kevlar-wrapped cables that increase resistance to wear while simultaneously reducing tangles.
To be honest, I was looking at the M50 because I knew another person that had them & was very happy with them, also I read reviews online which were positive. However, I didn’t realize until now that the possibilities are pretty endless when it comes to headphones, which is why I was asking for some direction… It just sucks cause my budget is definitely limited…
The outer shells of in-ear headphones are made up of a variety of materials, such as plastic, aluminum, ceramic and other metal alloys. Because in-ear headphones engage the ear canal, they can be prone to sliding out, and they block out much environmental noise. Lack of sound from the environment can be a problem when sound is a necessary cue for safety or other reasons, as when walking, driving, or riding near or in vehicular traffic.[19]
Ok, it’s been a month and a lot of new experience. I’ve auditoned ATH M-50 (clamp’s too tight; they sweat my ears just from few minutes of exposure) and Senn HD 600 (the velour pad is amazingly comfortable & size is ok). So, long story short, now I can refine my search to: circumaural&non-pleather/foam pads, which brought me to Senn HD 439 (cloth) & 518 (velour).
If you have a bass problem you could find a filter of some kind that cuts the low bass. Some bass controls can do that. I haven’t found a music genre that totally lacks strong bass, although “acoustic” sometimes doesn’t have strong bass. Mainly, you should make sure your system is matched properly with amp and headphone, so the different frequencies are in balance. Then you will have better luck with different music.
A balanced armature is a sound transducer design primarily intended to increase the electrical efficiency of the element by eliminating the stress on the diaphragm characteristic of many other magnetic transducer systems. As shown schematically in the first diagram, it consists of a moving magnetic armature that is pivoted so it can move in the field of the permanent magnet. When precisely centered in the magnetic field there is no net force on the armature, hence the term 'balanced.' As illustrated in the second diagram, when there is electric current through the coil, it magnetizes the armature one way or the other, causing it to rotate slightly one way or the other about the pivot thus moving the diaphragm to make sound.
With small extrusions emerging from otherwise understated wireless in-ears, Jabra’s Elite Active 65t look like miniature versions of the Bluetooth headsets that helped put the brand on the map. But don’t be fooled by the looks — with sweatproofing, excellent sound quality, and a myriad of useful features, these little guys beat out every other pair of headphones on the market as the best workout headphones.
In-ear headphones are like earbuds but are an upgrade to them. These headphones fit into the wearer's ear canal and stay in place with the use of foam or rubber tips. These tips are available in custom sizes so they can fit each individual wearer. When a proper fit's achieved, in-ear headphones reduce outside noise and deliver sound quality at about the same level as over-ear and on-ear headphones.
×