Dale: There are so many types of amplifiers (and DAC’s with amplifiers) that there is no shortcut for studying all of the options, unless you settle for the most generic approach. Important things to consider are power – if you don’t have enough power for your headphone and the dynamics in the music, clipping will result. Sometimes the clipping is “soft” and not readily noticed, but eventually you would discover that much of the detail goes missing or gets veiled with limited dynamics. Another consideration is whether to use a DAC, which may be a separate DAC or built into the same enclosure as the amp. Most DACs will improve the sound over the DACs that are built into computers, but when a DAC is available to replace the DAC built into most cellphones and low to mid-priced music players, you can usually expect a much greater improvement.
Their combination of dual balanced-armature drivers matched with a dynamic driver to pump up the lower end are kind of engineering normally found on products that cost more than double the price of the 1Mores. Even the smaller details are very well ironed out, such as Kevlar-wrapped cables that increase resistance to wear while simultaneously reducing tangles.
A. It can be difficult, so buy earbuds that include silicone tips in multiple sizes. Everyone’s ears are unique, so most earbud manufactures include small, medium, and large silicone tips that you can easily swap out. If you want a particularly snug fit, consider getting third-party earphone tips made of memory foam, which will always adjust to the contours of your ears.
I’ve never enjoyed the audio quality of Bluetooth headphones, but that’s just me. The sound is better than it ever has been, and it’ll get you 90% of the way there—but not everybody is willing to make that tradeoff. Since USB-C headphones have largely ceded their market advantages over Bluetooth, we have to examine the consumer audio technology’s performance in a world where the headphone jack is disappearing.

An electret driver functions along the same electromechanical means as an electrostatic driver. However the electret driver has a permanent charge built into it, whereas electrostatics have the charge applied to the driver by an external generator. Electret and electrostatic headphones are relatively uncommon. Original electrets were also typically cheaper and lower in technical capability and fidelity than electrostatics. Patent applications from 2009-2013 have been approved that show by using different materials, i.e. a "Fluorinated cyclic olefin electret film", Frequency response chart readings can reach 50 kHz at 100db. When these new improved electrets are combined with a traditional dome headphone driver, headphones can be produced that are recognised by the Japan Audio Society as worthy of joining the Hi Res Audio program. US patents 8,559,660 B2. 7,732,547 B2.7,879,446 B2.7,498,699 B2.
Interestingly, yesterday I was comparing my beyer 770 with my AT ath30 and then I realised how important it is also the soundstage, the good separation of instruments … finally I have decided I want to take this into account as well, and not only the issue of bass, midrange and treble … Since, in my opinion lack of bass we can try to fix it, but lack of soundstage is impossible, right?
Hi. I have more or less decided that the Philips Fidelio L1s are the ones for me. I plan to use them on my commute paired with an iPhone or the iPad as the source. I listen to a mix of pop, rock, blues and jazz so I’m not after boosting bass but I might want to fiddle with the dial on the treble and mids. Which brings me to my question. You state in your review that the L2s pair well with the Fiio e17 which lets you independently adjust treble and bass. Could the same effect be achieved lower down the $$ curve via a combination of say a Fiio E6 (for signal amplification) and a Dirac or Accudio app for equalisation?
A good headphone should last 25 years. The first thing to replace is earpads usually, since wear affects the sound. Sometimes the cable will get a loose connection and need replaced. The drivers should be good forever, but in some rare cases a hair can work its way in and cause a buzz or rattle. If that happens it’s usually easy to remove an earpad and pull the hair etc. out.
We are excited to announce that we are moving! To better serve our customers we will be moving from our current location on Morganton Blvd to Harper Ave across from McDonald’s in Lenoir (the old Music Center Location). We have closed our location on Morganton Blvd and will reopen at our Harper Ave. location on Wednesday. Due to the move, we may not be able to answer the store phone. For any questions, please message us here on Facebook or email us at [email protected] We can’t wait for you all to see the new RadioShack of Lenoir!
×