I see, yes, but that should serve as an important lesson – the soundstage is not real in the same sense as actual tones, bass, treble, whatever. Soundstage is a perception that’s based on many factors, and here’s a challenge for you: You should be able to find some music tracks that have better soundstage on one headphone, and other tracks that will be better on the other headphone. Most of the time it will be just one way, but when a closed headphone beats an open headphone, I expect the open headphone will still show an advantage on some tracks. Your hearing perception could be tricked by simple things like a recess or emphasis in certain frequency ranges, or even phase shift when more than one driver is in the cup.
Historically, many headphones had relatively high impedance, often over 500 ohms so they could operate well with high-impedance tube amplifiers. In contrast, modern transistor amplifiers can have very low output impedance, enabling lower-impedance headphones. Unfortunately, this means that older audio amplifiers or stereos often produce poor-quality output on some modern, low-impedance headphones. In this case, an external headphone amplifier may be beneficial.
Dale: The examples listed above are good general rules, but there also are so many exceptions and in-betweens that it also could be better to understand what is needed for your music, so you can narrow the search to the most appropriate headphones. For example, you may have heard that Classical music is a particular genre, but within that ‘genre’ are many very different types of music. Chamber music or pipe organ music may benefit from a headphone that’s highly detailed in the treble (a headphone that some users might say is bright), while harpsichord music and music that has a lot of strong trumpet sounds might be better served with a more rounded or softer treble.

A balanced armature is a sound transducer design primarily intended to increase the electrical efficiency of the element by eliminating the stress on the diaphragm characteristic of many other magnetic transducer systems. As shown schematically in the first diagram, it consists of a moving magnetic armature that is pivoted so it can move in the field of the permanent magnet. When precisely centered in the magnetic field there is no net force on the armature, hence the term 'balanced.' As illustrated in the second diagram, when there is electric current through the coil, it magnetizes the armature one way or the other, causing it to rotate slightly one way or the other about the pivot thus moving the diaphragm to make sound.


Total harmonic distortion: True, headphones with lower actual total harmonic distortion (THD) will sound better than those with higher THD. But the quoted THD numbers -- "less than 1 percent" -- aren't helpful in predicting sound quality. Listen to recordings of simply recorded acoustic guitar to assess the distortion of one set of headphones versus another. Some will sound appreciably cleaner than others.
Wired headphones are attached to an audio source by a cable. The most common connectors are 6.35 mm (¼″) and 3.5 mm phone connectors. The larger 6.35 mm connector is more common on fixed location home or professional equipment. The 3.5 mm connector remains the most widely used connector for portable application today. Adapters are available for converting between 6.35 mm and 3.5 mm devices.
Hearing risk from headphones' use also applies to workers who must wear electronic or communication headsets as part of their daily job (i.e., pilots, call center and dispatch operators, sound engineers, firefighters, etc.) and hearing damage depends on the exposure time. The National Institute for Occupational Safety and Health (NIOSH) recommends sound exposure not exceed 85 dB(A) over 8 hour work day as a time-weighted average.[35] NIOSH uses the 3-dB exchange rate often referred to as "time-intensity tradeoff" which means if sound exposure level is increased by 3 decibels, the duration of exposure should be cut in half. NIOSH published several documents targeted at protecting the hearing of workers who must wear communication headsets such as call center operators,[36] firefighters,[37] and musicians and sound engineers.[38]

Portability can mean many things, such as appearance in public, having a secure fit so the headphone doesn’t shift off of your ears, amount of isolation from ambient noise (including active noise canceling), whether the headphone can be worn around the neck when not listening or it requires a carry case, and when extra amplification is required, whether a suitable amp can be found that’s OK to carry along with the portable music player.


Passive noise isolation is essentially using the body of the earphone, either over or in the ear, as a passive earplug that simply blocks out sound. The headphone types that provide most attenuation are in-ear canal headphones and closed-back headphones, both circumaural and supra aural. Open-back and earbud headphones provide some passive noise isolation, but much less than the others. Typical closed-back headphones block 8 to 12 dB, and in-ears anywhere from 10 to 15 dB. Some models have been specifically designed for drummers to facilitate the drummer monitoring the recorded sound while reducing sound directly from the drums as much as possible. Such headphones claim to reduce ambient noise by around 25 dB.

In the professional audio sector, headphones are used in live situations by disc jockeys with a DJ mixer, and sound engineers for monitoring signal sources. In radio studios, DJs use a pair of headphones when talking to the microphone while the speakers are turned off to eliminate acoustic feedback while monitoring their own voice. In studio recordings, musicians and singers use headphones to play or sing along to a backing track or band. In military applications, audio signals of many varieties are monitored using headphones.
The Samsung Galaxy Buds are one of the best-scoring portable Bluetooth headphones Consumer Reports has ever tested. That’s all the more impressive given their “true wireless” design, meaning the model doesn’t have a cord connecting the left earbud to the right. That’s the same design scheme popularized by Apple’s AirPods, but our testers say the Galaxy Buds sound dramatically better.
The Elite Active 65t come with three sets of silicone tips and feature an ergonomic design that guarantees a good seal, which is a big reason we prefer them to other true wireless models. With outstanding comfort and excellent passive noise isolation, you get the most out of every note, and you can also lower the volume for less ear strain. Overall sound quality is solid, and sound comes through clear and balanced, with a punchy bass response and a surprisingly dynamic treble range.
A. It can be difficult, so buy earbuds that include silicone tips in multiple sizes. Everyone’s ears are unique, so most earbud manufactures include small, medium, and large silicone tips that you can easily swap out. If you want a particularly snug fit, consider getting third-party earphone tips made of memory foam, which will always adjust to the contours of your ears.

Anyway, I’m looking for comfortable headphones for casual listening from my mobile phone, and so far I’m uncomfortable with portables. I have tried many portables in multiple stores, they sweat my ears after few minutes, and their small size never cover my ears properly. Recently I have experienced one of Clarion headphone (dunno which series, its price around Rp 99.000), while its big ear cushion cover my ears properly, I felt too much pressure on the area below my ears, probably due to its weight..
Benefits of Portable Generators best bicycle engine kit Best Gaming Laptop for Overwatch Best Generator best inversion tables Best Jump Starter best laptop best light therapy lamp best night visions goggles best overwatch laptops best record players best standing desks best stands best treadmills best wireless printers bluetooth dslr Electric generator tips How Does a Movie Projector Work? how much processor speed do i need How often should you buy a new computer How Often Should You Replace Your Laptop How to Set Up Headphones on PC Important Features of Portable Generators Intel Optane Vs SSD Benchmark Portable professional reviews Something About Best Quiet Portable Generator travel turntable under $300 under $500 under $1000 under 200$ Video Editing What is a Fast Processor Speed for a Laptop What is Backlit Keyboard Laptop? What Processor Do I Need for Gaming What Processor is Good for Gaming What Processor Speed Do I Need for My Laptop when should you get a new laptop Windows wireless
If you want headphones for gaming or watching movies, get some that support multi-channel surround sound. Some high-end headphones include technology that simulates surround sound, so sound effects feel like they’re coming from different directions. These headphones do a surprisingly good job at replicating the home theater experience and create an immersive experience for listeners. If you’re into big-budget blockbusters or first-person shooters and don’t have the room for a full-blown surround sound system, go for the next best thing and get headphones that support multi-channel audio.
Headphones can prevent other people from hearing the sound, either for privacy or to prevent disturbing others, as in listening in a public library. They can also provide a level of sound fidelity greater than loudspeakers of similar cost. Part of their ability to do so comes from the lack of any need to perform room correction treatments with headphones. High-quality headphones can have an extremely flat low-frequency response down to 20 Hz within 3 dB. While a loudspeaker must use a relatively large (often 15" or 18") speaker driver to reproduce low frequencies, headphones can accurately reproduce bass and sub-bass frequencies with speaker drivers only 40-50 millimeters wide (or much smaller, as is the case with in-ear monitor headphones). Headphones' impressive low-frequency performance is possible because they are so much closer to the ear that they only need to move relatively small volumes of air.
If you’ve been on an airplane in the last few years, you’ve probably seen the Bose QuietComfort noise-cancelling headphones before: they’re a favorite of regular travelers because they’re so good at keeping outside noise out. They’re comfortable, they sound incredible, and the noise cancellation is so impressive that you feel like you’re in your own personal bubble. These headphones are not cheap, but they’re definitely worth the money.
Recently released this summer, the Headphones 700 are the best wireless over-ear headphones that Bose has to over. The combine the best-in-class noise-cancellation with great audio quality. Other than the design overhaul, the biggest difference from the QuietComfort 35 II is that the Headphones 700 have a significantly upgraded microphone array. This allows the headphones to have a wonderful tranparancy mode (or ambient listening mode), and makes maybe the best headphones you can buy for call quality.
Frequency response: Frequency-response specifications in full-size loudspeakers are generally pretty useless in predicting sound quality, but headphone frequency-response numbers are even worse. Manufacturers have routinely exaggerated frequency-response figures to the point that they're irrelevant. Even the flimsiest, cheap headphones routinely boast extremely low bass-response performance --15Hz or 20Hz -- but almost always sound lightweight and bright. Generally, bass buffs will be happier sticking with larger 'phones.
Electrostatic drivers consist of a thin, electrically charged diaphragm, typically a coated PET film membrane, suspended between two perforated metal plates (electrodes). The electrical sound signal is applied to the electrodes creating an electrical field; depending on the polarity of this field, the diaphragm is drawn towards one of the plates. Air is forced through the perforations; combined with a continuously changing electrical signal driving the membrane, a sound wave is generated. Electrostatic headphones are usually more expensive than moving-coil ones, and are comparatively uncommon. In addition, a special amplifier is required to amplify the signal to deflect the membrane, which often requires electrical potentials in the range of 100 to 1000 volts.
AAC has some advantages when it comes to latency, but we recommend avoiding this if you care about audio quality. We found high levels of noise and lower than average frequency cutoffs—both unacceptable to audiophiles and younger listeners. Though the sound isn’t as bad as some may make it out to be, the shortcomings are noticeable to the human ear at normal listening volumes.
While noise-canceling headphones are what it’s best known for, Bose makes plenty of other high-quality headphones and earbuds for people who don’t want or need noise cancellation, which degrades audio quality and costs a premium. From true wireless AirPod competitors to old-school wired earbuds, to just cheaper wireless over-ear cans, Bose makes a headphone for every style and, more importantly, for every budget.
Wireless and truly wireless: These connect to your devices using Bluetooth, so you’re never physically tethered to your smartphone, tablet, or computer. Wireless headphones don’t use a wire to connect to an audio source, but they do use a wire to connect the two earpieces together. In contrast, “truly” wireless headphones come as two separate earpieces that don’t need wires to connect to anything. Wireless headphones are incredibly affordable; truly wireless headphones can cost anywhere from $100 to $400.

Open back usually results in more natural sound, but they leak sound in and out. This means you probably can’t use them in a library or a plane flight since the sound of your music will leak out and disturb the people around you. You also can’t use them on loud public places since noise from the outside will disturb your music. Therefore, even though open back would give you more natural reproduction, for these reasons their use is limited to mostly at home or in the office (if you have your own space that is).

Noise cancellation: Noise-cancelling headphones play specific tones, much like white noise, to cancel out all of the sound around you and allow you to enjoy your music uninterrupted. Noise-cancellation is an active process, so headphones with this feature require batteries. If you’re a frequent flyer, or if you’ve got a noisy commute to work each day, you’ll love noise-cancelling headphones: they’re fantastic at keeping the cacophony of the outside world at bay.


The QuietComfort 20 headphones have been around for years and years; and they’re essentailly an in-ear alterative to Bose’s QuietComfort 25. They offer the same great active noise-cancellation that the company is known for, just in a traditional wired and in-ear form factor. The QuietComfort 20 can also be switched to an “Aware” (aka ambient) mode, so you can better hear the world around you.
The Astro Gaming A50 emerged in 2012 as the wireless follow-up to the excellent A40. Seven years later and four generations on, they remain the gold standard for gaming audio. With an ability to faithfully reproduce 7.1 channel surround sound through just two earcups, gamers will get critical 3D audio for all of their favorite console titles whether it’s from an Xbox One or a PlayStation 4. Wireless audio can lead to an unacceptable amount of lag, which often sends gamers in search of wired models, but here too, the A50 manage to beat expectations.

I’m a former Mixer and DJ and I’d highly recommend the Beyer T1 for mixing. It is not absolutely flat, but it is an all around proper Audio Technicians Headphone. For flat response, I might eyeball the HD800 but the low end might not be the best if you are often mixing tracks with solid low ends. Flat might not always be the best option ( my opinion ). If you need to mix heavy bass tracks, it is better to have a headphone that responds better to low end EQ and is generally accepted as a more well rounded headphone.


Garbage in = Garbage out (GIGO) is a popular phrase used to emphasize the importance of a good source. This can be the soundcard in your laptop, the quality of your portable audio player, or the CD player you’re using for music listening. Those fall into the “Source” category. The better your source is, the better the sound will be at the headphone end. This is why we are seeing more and more audiophile digital audio players (audiophile DAPs). They are expensive but they sound good.

The adage that you get what you pay for is generally true for audio products like headphones. What has made us big fans of the 1More brand is its ability to redefine that expectation in surprising ways. The 1More Triple Driver in-ear headphones are a great example of this: They exhibit all of the hallmarks of high-end, expensive earbuds, yet manage to keep the price highly affordable for most people.
A: What you plug your headphones into can significantly affect their sound, and the quality of the amplifiers built into portable CD/MP3 players is generally awful. It's not their fault: the little guys have to power their electronics and their internal amplifier using a few puny volts. Even some of the better home AV receivers' headphone jacks offer highly variable sound quality.
One thing I suggest to prospective customers for a specific headphone, if I have that headphone on hand, is for them to suggest 2 or 3 music tracks by a particular artist and composer that I can sample on that headphone, not so much for me to suggest how it sounds, but mostly to check if that headphone has any real sonic issues with that music. For example, a headphone that’s ideal for classical and acoustic music might sound too harsh with metal and industrial goth.

These headphones pack about 16 hours of battery life, which ought to be enough for a whole day or more, but if not, there’s always the option of using an analog cable instead. An external switch lets you turn the noise cancellation on and off. Make no mistake, these might be aimed at kids, but the quality of construction, selection of materials, and color choices give them an appearance that will still appeal to your young charges long after they’ve outgrown their Disney phase (some of us still haven’t).

Earbuds have small speakers that rest on the ear canal of the wearer. These are usually much less expensive than on-ear and over-ear headphones and reproduce the sound well. However, outside sounds, such as traffic or power tools, can get past the earbuds and interfere with your enjoyment. Earbuds also don't stay in place very well if the wearer is moving much, such as exercising. These also are lower fidelity than on-ear and over-ear headphones.
×