That depends on what you’re using them for and how much you’re willing to spend. At the high-end, over-ear and in-ear headphones can both perform fantastically. For those of us not willing to spend thousands on headphones, over-ear headphones typically offer better bass response and a bigger soundstage, but in-ear headphones are significantly more portable and convenient — especially wireless earbuds.
A headset is a headphone combined with a microphone. Headsets provide the equivalent functionality of a telephone handset with hands-free operation. Among applications for headsets, besides telephone use, are aviation, theatre or television studio intercom systems, and console or PC gaming. Headsets are made with either a single-earpiece (mono) or a double-earpiece (mono to both ears or stereo). The microphone arm of headsets is either an external microphone type where the microphone is held in front of the user's mouth, or a voicetube type where the microphone is housed in the earpiece and speech reaches it by means of a hollow tube.
hi? i want to ask a question. Im a complete newbie on the audiphilic side so i red on a site that the more the impedance is higher a headphone amp is requierd and less the impedance a headphone amp is not that much requierd cause the headphones with less impedance are made for portable players. Now let me get to the point im using cheap headphones the philips sbc hp250 they are old about 5 years and sound ok but i want to replace them so i use them mostly for listening to hours of music and i am also a musician so would it make a diference if i would buy a behringer headphone amp http://www.amazon.com/Behringer-HA400-4-Channel-Stereo-Headphone/dp/B000KIPT30/ref=sr_1_6?ie=UTF8&qid=1379715994&sr=8-6&keywords=behringer+amplifier and amplify those headphones would they play better cause now im having them plugged on a intergrated via vinyl soundcard http://www.via.com.tw/en/products/audio/codecs/vt1708s/. and they sound shitty on full volume. I am considering to buy new full size headphones and im willing to give max 80 euros for them so for the start i just want them to be loud but i want a clear sound at high volume levels. To be more specific i want a clear sound that is balanced in the lows mids and highs but not distorted and the lows should not be too much overpowered. I was sniffing around your site and found some sennheiser hd 202 ii they are not even close to 80 euros but i heard they sound great would they be better than these philips headphones and what other alternatives would you suggest me for max 80 euros
The WH-1000xM3’s excellent noise-canceling technology ranks second only to the Bose QC35 II, from the brand that has long dominated the market in terms of sheer noise-blocking abilities. That said, the Sony cans sound much better than the new bass-forward Bose option, and offer numerous features that help to create a much better overall experience.
The usual way of limiting sound volume on devices driving headphones is by limiting output power. This has the additional undesirable effect of being dependent of the efficiency of the headphones; a device producing the maximum allowed power may not produce adequate volume when paired with low-efficiency, high-impedance equipment, while the same amount of power can reach dangerous levels with very efficient earphones.
For older models of telephones, the headset microphone impedance is different from that of the original handset, requiring a telephone amplifier for the telephone headset. A telephone amplifier provides basic pin-alignment similar to a telephone headset adaptor, but it also offers sound amplification for the microphone as well as the loudspeakers. Most models of telephone amplifiers offer volume control for loudspeaker as well as microphone, mute function and switching between headset and handset. Telephone amplifiers are powered by batteries or AC adaptors.
Dale: The examples listed here are good general rules, but one thing to keep in mind is in the mid-to-lower price tiers, open-back headphones aren’t nearly as common as the closed types. The smaller list of choices, and the more limited reviews of those items, could make getting a perfect fit more difficult. Sound stage and openness are often given as the advantage of the open-back types, but it’s just a general rule and some closed-back headphones excel at those properties. An important thing to consider is the music itself, since sound stage and perspective varies widely in different recordings.
Circumaural headphones (sometimes called full size headphones or over-ear headphones) have circular or ellipsoid earpads that encompass the ears. Because these headphones completely surround the ear, circumaural headphones can be designed to fully seal against the head to attenuate external noise. Because of their size, circumaural headphones can be heavy and there are some sets that weigh over 500 grams (1 lb). Ergonomic headband and earpad design is required to reduce discomfort resulting from weight. These are commonly used by drummers in recording.
At the heart of the WH-1000xM3 is outstanding wireless sound. Sony’s LDAC technology delivers a wireless signal at what the company claims is three times the quality of standard Bluetooth streaming, and the headphones also support the latest aptX HD codec (with supported devices). The 1000xM3 even “upscale” wireless music from high-resolution audio devices using a special chip, helping to make music sound dynamic and beautiful, with authoritative bass and clear treble response held together by a well-rounded midrange.

The FiiO E17 “Alpin” + AIAIAI TMA-1 or Pro700 Mk2 seem like a mix you’d recommend, but I’m concerned those cans will be uncomfortable for day-long use.  Also I don’t know if that DAC/amp is the best for my style of music/headphones.  Third, some of my techno tracks have stunning vocals, and I don’t want to miss out on those high notes while enjoying the bass.

The Bose QuietComfort 25 were released in 2015 and you can still buy them today. They are kind of like a wired version of the Bose QuietComfort 35. They have a slightly dated look, and boast almost as good levels of active noise-cancellation and sound quality as Bose’s QuietComfort 35. The important thing to remember is that even though these are wired headphones, they still need to be charged so you can turn on the active noise cancellation. Otherwise, they just work as normal over-ear headphones.

Circumaural headphones (sometimes called full size headphones or over-ear headphones) have circular or ellipsoid earpads that encompass the ears. Because these headphones completely surround the ear, circumaural headphones can be designed to fully seal against the head to attenuate external noise. Because of their size, circumaural headphones can be heavy and there are some sets that weigh over 500 grams (1 lb). Ergonomic headband and earpad design is required to reduce discomfort resulting from weight. These are commonly used by drummers in recording.
The problem is made even worse by the fact that Android phones can’t handle AAC in a method that approaches Apple’s performance with the codec. Consequently, we will no longer be recommending AAC-only headsets here at SoundGuys, as the experience is that broken from source to source. The results are crappier and noisier than the other codecs by a longshot.
Just a few hours of burn-in today – I don’t expect much change with Tesla-quality drivers etc. The treble is recessed almost as much as the Philips M1 I had, kind-of a worst-case scenario. So I took out my most minimal non-peaky non-bright non-sibilant headphone – the B&O H6, and even though it doesn’t sound the same as the T51p because of the H6’s “light” midrange, I wanted to get a sense of how much the T51p was recessed below a very minimal treble. My Foobar2000 settings were +2 at 2.5, +4 at 3.5, +2 at 5, +4 at 7, +6 at 10, 14, and 20 khz. Normally I wouldn’t do the dip at 5 khz, but the T51p has a nasty 10 db peak around 5 khz, which makes it difficult for portable use without a customizable equalizer. Without a treble boost it sounds very boomy as well as muffled. I can understand Beyer going to a darker sound with more bass – in fact I thought it was a move in the right direction. But they need to cut that (resonant?) peak around 5 khz. I compared to several other headphones and none of those were anything like that.
Total harmonic distortion: True, headphones with lower actual total harmonic distortion (THD) will sound better than those with higher THD. But the quoted THD numbers -- "less than 1 percent" -- aren't helpful in predicting sound quality. Listen to recordings of simply recorded acoustic guitar to assess the distortion of one set of headphones versus another. Some will sound appreciably cleaner than others.
The Astro Gaming A50 emerged in 2012 as the wireless follow-up to the excellent A40. Seven years later and four generations on, they remain the gold standard for gaming audio. With an ability to faithfully reproduce 7.1 channel surround sound through just two earcups, gamers will get critical 3D audio for all of their favorite console titles whether it’s from an Xbox One or a PlayStation 4. Wireless audio can lead to an unacceptable amount of lag, which often sends gamers in search of wired models, but here too, the A50 manage to beat expectations.

Unlike with other codecs, AAC test signals from Android phones like the Huawei P20 Pro, LG V30, and Samsung Galaxy Note 8 all vary wildly. Though we can’t definitively say why each Android device seems to handle AAC encoding differently, the fact of the matter is that only Apple can do it well. We suspect some of the power saving features baked into the Google ecosystem’s varying hardware has consequences for audio playback. Nowhere is this more apparent than Huawei’s power-sipping P20 Pro, which seems to cut out at around 14.25kHz.
Electrostatic drivers consist of a thin, electrically charged diaphragm, typically a coated PET film membrane, suspended between two perforated metal plates (electrodes). The electrical sound signal is applied to the electrodes creating an electrical field; depending on the polarity of this field, the diaphragm is drawn towards one of the plates. Air is forced through the perforations; combined with a continuously changing electrical signal driving the membrane, a sound wave is generated. Electrostatic headphones are usually more expensive than moving-coil ones, and are comparatively uncommon. In addition, a special amplifier is required to amplify the signal to deflect the membrane, which often requires electrical potentials in the range of 100 to 1000 volts.
hum..I see your point…The big concern to me is that, since I don´t live in USA, everytime I order a pair of cans if I don´t like it I sell it….That´s the reason I will order starting with the most popular brands… it will be easier for me to pass a senn than a superlux, for instance. You know what I mean? Since you have mentioned 598 and HP100, can you please tell me who wins in terms of soundstage, spaciousness, and good separation?
Those who buy either of these headphones are in for a treat. Our reviewer didn’t hold back in their assessment of these cans’ ability to fully realize every detail of a recording, noting their “warm and rigid bass, a midrange that dips close to the ruddy colors of analog tape saturation (without sacrificing an ounce of detail), and a laser tight response up top that helps illuminate vivid clarity and granular instrumental texture across the board.”
The WH-1000xM3’s advanced control systems allow you to let in various levels of ambient sound, with advanced features like voice-only mode, which helps filter through vocal frequencies so you can hear your music and the voices around you while blocking out other sounds. Responsive touch controls let you navigate volume, make calls, and play and pause music with ease, all while helping to maintain a clean aesthetic. Best of all, the WH-1000xM3 offer a staggering 30 hours of battery life, providing even heavy users with days of use from a single charge, and have a quick charge feature that allows you to enjoy five hours of listening after just 15 minutes of charging.
This type combines advantages of earbuds and in-ear headphones – depending on the environment and requirements of the user, they provide passive noise reduction for quality mode (conversation or active music listening) or they give control over the sound environment around user in comfort mode (stand by or background voice/music listening).[citation needed]
I tend to regard the M50 as the minimum for hi-fi listening with no apologies for limitations. But if you have to go cheaper than the usual $125 USD for the M50, the B&O Form2 with a simple bass boost gives a real hi-fi sound, and it should be available for about $100. The Beyer DTX-501P (similar to soundmagic P30) is good for $100, but needs a slight treble boost. The LSTN Fillmore with wood cups is somewhat colored, but still a good listen and good for $100. Below $100 are the Sennheiser PX series – not hi-fi by any means. There are several good IEMs below $100, and Apple Earpods with a Dirac or Accudio Pro player are very hi-fi, and cheap.

Expensive: Audiophile-grade headphones can cost anywhere between $130 and $2,000. Headphones in this price bracket are no joke: they create impressive soundscapes, are robust enough for use in a recording studio, and they’re just plain beautiful. If you need a pair of headphones for critical listening, or you simply want the best headphones around, it’ll cost you.


This is better than I thought it would be. Worst case is the T51p won’t have the excitement of the more “V”-shaped headphone sounds, but you’ll hear more of what’s actually in the recording. The more neutral headphones are most often a little bright (that’s what most users say), and can irritate on electronic and improvised music, but the T51p didn’t show any of that with these 3 tracks.
Wired headphones are attached to an audio source by a cable. The most common connectors are 6.35 mm (¼″) and 3.5 mm phone connectors. The larger 6.35 mm connector is more common on fixed location home or professional equipment. The 3.5 mm connector remains the most widely used connector for portable application today. Adapters are available for converting between 6.35 mm and 3.5 mm devices.
×