Dale: It’s really the same with any genre or sub-genre of music, that the sound from different artists and tracks can vary a lot, so having more than one headphone is a plus. When only one headphone is available at a particular time (portable use especially), one option is to use a headphone that can accommodate a wide range of genres, in which case there may be compromises to consider. Another option is to carry two headphones – one on the head or around the neck and another in a carry case. Some of the small headphones can make this easy to do.
Pairing high sensitivity headphones with power amplifiers can produce dangerously high volumes and damage headphones. The maximum sound pressure level is a matter of preference, with some sources recommending no higher than 110 to 120 dB. In contrast, the American Occupational Safety and Health Administration recommends an average SPL of no more than 85 dB(A) to avoid long-term hearing loss, while the European Union standard EN 50332-1:2013 recommends that volumes above 85 dB(A) include a warning, with an absolute maximum volume (defined using 40–4000 Hz noise) of no more than 100 dB to avoid accidental hearing damage. Using this standard, headphones with sensitivities of 90, 100 and 110 dB (SPL)/V should be driven by an amplifier capable of no more than 3.162, 1.0 and 0.3162 RMS volts at maximum volume setting, respectively to reduce the risk of hearing damage.
Open back usually results in more natural sound, but they leak sound in and out. This means you probably can’t use them in a library or a plane flight since the sound of your music will leak out and disturb the people around you. You also can’t use them on loud public places since noise from the outside will disturb your music. Therefore, even though open back would give you more natural reproduction, for these reasons their use is limited to mostly at home or in the office (if you have your own space that is).
Headphones can prevent other people from hearing the sound, either for privacy or to prevent disturbing others, as in listening in a public library. They can also provide a level of sound fidelity greater than loudspeakers of similar cost. Part of their ability to do so comes from the lack of any need to perform room correction treatments with headphones. High-quality headphones can have an extremely flat low-frequency response down to 20 Hz within 3 dB. While a loudspeaker must use a relatively large (often 15" or 18") speaker driver to reproduce low frequencies, headphones can accurately reproduce bass and sub-bass frequencies with speaker drivers only 40-50 millimeters wide (or much smaller, as is the case with in-ear monitor headphones). Headphones' impressive low-frequency performance is possible because they are so much closer to the ear that they only need to move relatively small volumes of air.
What I’m saying here is that it’s better to own three $100 headphones than one $300 headphone. Or three $300 headphones than one $900 headphone. Why? Because most people don’t limit their playlist to strictly one genre. And following the logic from Rule #2, the right headphone-music pairing is going to be better than one expensive headphone paired to the wrong music.
Binaural recordings use a different microphone technique to encode direction directly as phase, with very little amplitude difference below 2 kHz, often using a dummy head. They can produce a surprisingly lifelike spatial impression through headphones. Commercial recordings almost always use stereo recording, rather than binaural, because loudspeaker listening is more common than headphone listening.
Despite big promises from Bluetooth’s only Hi-res codec, the standard doesn’t really deliver at best, and it falls far short with its basic 330kbps setting. Both the 660kbps and 990kbps connections offer decent quality, but the 330kbps setting has a lot of noise—and a comparatively poor frequency response with higher-def content. You probably won’t hear it, but it definitely falls short of the marketing.
The problem is made even worse by the fact that Android phones can’t handle AAC in a method that approaches Apple’s performance with the codec. Consequently, we will no longer be recommending AAC-only headsets here at SoundGuys, as the experience is that broken from source to source. The results are crappier and noisier than the other codecs by a longshot.
A: What you plug your headphones into can significantly affect their sound, and the quality of the amplifiers built into portable CD/MP3 players is generally awful. It's not their fault: the little guys have to power their electronics and their internal amplifier using a few puny volts. Even some of the better home AV receivers' headphone jacks offer highly variable sound quality.
Just a few hours of burn-in today – I don’t expect much change with Tesla-quality drivers etc. The treble is recessed almost as much as the Philips M1 I had, kind-of a worst-case scenario. So I took out my most minimal non-peaky non-bright non-sibilant headphone – the B&O H6, and even though it doesn’t sound the same as the T51p because of the H6’s “light” midrange, I wanted to get a sense of how much the T51p was recessed below a very minimal treble. My Foobar2000 settings were +2 at 2.5, +4 at 3.5, +2 at 5, +4 at 7, +6 at 10, 14, and 20 khz. Normally I wouldn’t do the dip at 5 khz, but the T51p has a nasty 10 db peak around 5 khz, which makes it difficult for portable use without a customizable equalizer. Without a treble boost it sounds very boomy as well as muffled. I can understand Beyer going to a darker sound with more bass – in fact I thought it was a move in the right direction. But they need to cut that (resonant?) peak around 5 khz. I compared to several other headphones and none of those were anything like that.