Dale: There are so many types of amplifiers (and DAC’s with amplifiers) that there is no shortcut for studying all of the options, unless you settle for the most generic approach. Important things to consider are power – if you don’t have enough power for your headphone and the dynamics in the music, clipping will result. Sometimes the clipping is “soft” and not readily noticed, but eventually you would discover that much of the detail goes missing or gets veiled with limited dynamics. Another consideration is whether to use a DAC, which may be a separate DAC or built into the same enclosure as the amp. Most DACs will improve the sound over the DACs that are built into computers, but when a DAC is available to replace the DAC built into most cellphones and low to mid-priced music players, you can usually expect a much greater improvement.
The QuietComfort 30s are Bose’s wireless in-ear headphones with active noise cancellation, and they’ve set the bar for the category since they were released in 2016. The QuietComfort 30s utilize the same StayHear+ tips as all Bose’s other in-ear headphones and they use the same app as the company’s other QuietComfort headphones. The one caveat is that the QuietComfort 30s are a neckband-style of wireless headphone, so they’re fairly heavy and probably best served for office settings.
The moving coil driver, more commonly referred to as a "dynamic" driver is the most common type used in headphones. It consists of a stationary magnet element affixed to the frame of the headphone, which sets up a static magnetic field. The magnet in headphones is typically composed of ferrite or neodymium. A voice coil, a light coil of wire, is suspended in the magnetic field of the magnet, attached to a diaphragm, typically fabricated from lightweight, high-stiffness-to-mass-ratio cellulose, polymer, carbon material, paper or the like. When the varying current of an audio signal is passed through the coil, it creates a varying magnetic field that reacts against the static magnetic field, exerting a varying force on the coil causing it and the attached diaphragm to vibrate. The vibrating diaphragm pushes on the air to produce sound waves.
Binaural recordings use a different microphone technique to encode direction directly as phase, with very little amplitude difference below 2 kHz, often using a dummy head. They can produce a surprisingly lifelike spatial impression through headphones. Commercial recordings almost always use stereo recording, rather than binaural, because loudspeaker listening is more common than headphone listening.

Every single Bluetooth codec has significant quality issues—despite many creative solutions employed to make the most of the limited bandwidth the standards employ. For those keeping score at home: not a single codec available can meet wired signal quality. Though Bluetooth audio has come a long way since its noisy beginnings, it’s still not ready to replace the headphone jack. Qualcomm’s aptx HD, and Sony’s LDAC 990kbps codecs come close, but everything else falls far short of the mark.
I’m a former Mixer and DJ and I’d highly recommend the Beyer T1 for mixing. It is not absolutely flat, but it is an all around proper Audio Technicians Headphone. For flat response, I might eyeball the HD800 but the low end might not be the best if you are often mixing tracks with solid low ends. Flat might not always be the best option ( my opinion ). If you need to mix heavy bass tracks, it is better to have a headphone that responds better to low end EQ and is generally accepted as a more well rounded headphone.
The usual way of limiting sound volume on devices driving headphones is by limiting output power. This has the additional undesirable effect of being dependent of the efficiency of the headphones; a device producing the maximum allowed power may not produce adequate volume when paired with low-efficiency, high-impedance equipment, while the same amount of power can reach dangerous levels with very efficient earphones.
Released in 2015, the SoundLink Around-Ear II are Bose’s wireless over-ear headphones that don’t have active noise cancellation. They’re lighter and slightly more travel-friendly than a lot of the company’s other offerings, and they could sound quality at the forefront. At the time, the big selling point for the SoundLink Around-Ear II was their sound quality — Bose claimed that they sounded as good as wired headphones, which admittedly doesn’t hold up in 2019 (streaming and Bluetooth have gotten too good).
The WH-1000xM3’s advanced control systems allow you to let in various levels of ambient sound, with advanced features like voice-only mode, which helps filter through vocal frequencies so you can hear your music and the voices around you while blocking out other sounds. Responsive touch controls let you navigate volume, make calls, and play and pause music with ease, all while helping to maintain a clean aesthetic. Best of all, the WH-1000xM3 offer a staggering 30 hours of battery life, providing even heavy users with days of use from a single charge, and have a quick charge feature that allows you to enjoy five hours of listening after just 15 minutes of charging.
A good headphone should last 25 years. The first thing to replace is earpads usually, since wear affects the sound. Sometimes the cable will get a loose connection and need replaced. The drivers should be good forever, but in some rare cases a hair can work its way in and cause a buzz or rattle. If that happens it’s usually easy to remove an earpad and pull the hair etc. out.
In-ear headphones are like earbuds but are an upgrade to them. These headphones fit into the wearer's ear canal and stay in place with the use of foam or rubber tips. These tips are available in custom sizes so they can fit each individual wearer. When a proper fit's achieved, in-ear headphones reduce outside noise and deliver sound quality at about the same level as over-ear and on-ear headphones.
×