The moving coil driver, more commonly referred to as a "dynamic" driver is the most common type used in headphones. It consists of a stationary magnet element affixed to the frame of the headphone, which sets up a static magnetic field. The magnet in headphones is typically composed of ferrite or neodymium. A voice coil, a light coil of wire, is suspended in the magnetic field of the magnet, attached to a diaphragm, typically fabricated from lightweight, high-stiffness-to-mass-ratio cellulose, polymer, carbon material, paper or the like. When the varying current of an audio signal is passed through the coil, it creates a varying magnetic field that reacts against the static magnetic field, exerting a varying force on the coil causing it and the attached diaphragm to vibrate. The vibrating diaphragm pushes on the air to produce sound waves.
Whether you wear headphones for your daily commute, regular workouts, or just for jamming out at home, you need a good pair that’s comfortable and can make everything sound great. Headphone tech has evolved significantly, too, so some pairs can do a lot more than just play sound. It’s not tough to find a pair that can connect to your smartphone wirelessly, or one that can keep outside commotion out.
These early headphones used moving iron drivers,[7] with either single-ended or balanced armatures. The common single-ended type used voice coils wound around the poles of a permanent magnet, which were positioned close to a flexible steel diaphragm. The audio current through the coils varied the magnetic field of the magnet, exerting a varying force on the diaphragm, causing it to vibrate, creating sound waves. The requirement for high sensitivity meant that no damping was used, so the frequency response of the diaphragm had large peaks due to resonance, resulting in poor sound quality. These early models lacked padding, and were often uncomfortable to wear for long periods. Their impedance varied; headphones used in telegraph and telephone work had an impedance of 75 ohms. Those used with early wireless radio had more turns of finer wire to increase sensitivity. Impedance of 1000 to 2000 ohms was common, which suited both crystal sets and triode receivers. Some very sensitive headphones, such as those manufactured by Brandes around 1919, were commonly used for early radio work.

Hi. I have more or less decided that the Philips Fidelio L1s are the ones for me. I plan to use them on my commute paired with an iPhone or the iPad as the source. I listen to a mix of pop, rock, blues and jazz so I’m not after boosting bass but I might want to fiddle with the dial on the treble and mids. Which brings me to my question. You state in your review that the L2s pair well with the Fiio e17 which lets you independently adjust treble and bass. Could the same effect be achieved lower down the $$ curve via a combination of say a Fiio E6 (for signal amplification) and a Dirac or Accudio app for equalisation?


The moving coil driver, more commonly referred to as a "dynamic" driver is the most common type used in headphones. It consists of a stationary magnet element affixed to the frame of the headphone, which sets up a static magnetic field. The magnet in headphones is typically composed of ferrite or neodymium. A voice coil, a light coil of wire, is suspended in the magnetic field of the magnet, attached to a diaphragm, typically fabricated from lightweight, high-stiffness-to-mass-ratio cellulose, polymer, carbon material, paper or the like. When the varying current of an audio signal is passed through the coil, it creates a varying magnetic field that reacts against the static magnetic field, exerting a varying force on the coil causing it and the attached diaphragm to vibrate. The vibrating diaphragm pushes on the air to produce sound waves.

The number one rule to understand when embarking on your headphone-search journey is to understand that there is no one headphone to rule them all. Like automobiles, headphones are made for different purposes. You have the supercars, roadsters, SUVs, 4x4s, sedans, to the compacts, and you chose what’s best for your day to day needs. There is no one car that can tackle snow and win races on the drag strip. The sooner you understand this fact, the more money you will save.


Active noise-cancelling headphones use a microphone, amplifier, and speaker to pick up, amplify, and play ambient noise in phase-reversed form; this to some extent cancels out unwanted noise from the environment without affecting the desired sound source, which is not picked up and reversed by the microphone. They require a power source, usually a battery, to drive their circuitry. Active noise cancelling headphones can attenuate ambient noise by 20 dB or more, but the active circuitry is mainly effective on constant sounds and at lower frequencies, rather than sharp sounds and voices. Some noise cancelling headphones are designed mainly to reduce low-frequency engine and travel noise in aircraft, trains, and automobiles, and are less effective in environments with other types of noise.
Noise cancelation for kids? Doesn’t that mean they’ll ignore their parents even more often than they already do? Perhaps, but it’s a risk worth taking if it means your kids’ hearing will be protected over the long-term. That’s exactly the premise behind the Puro PuroQuiet headphones. Not only are they wireless and great-sounding, but they also come equipped with a software limiter that keeps the volume at or below 85dB, which is considered the maximum volume that children should be exposed to for prolonged periods. The noise-canceling feature means they’ll actually be able to listen to lower (therefore safer) volumes.
Marketed claims such as 'frequency response 4 Hz to 20 kHz' are usually overstatements; the product's response at frequencies lower than 20 Hz is typically very small.[23] Headphones are also useful for video games that use 3D positional audio processing algorithms, as they allow players to better judge the position of an off-screen sound source (such as the footsteps of an opponent or their gunfire).
If you’ll mostly be using headphones at your desk, install a headphone hook so you can safely stow yours when you’re not using them. Headphones can be fairly fragile, so it’s important to take care of yours and avoid tossing them around. A headphone hook gives your favorite pair a place to hang and creates a fun conversation piece for your workstation.
Alternatively, online calculators can be used.[13] Once the sensitivity per volt is known, the maximum volume for a pair of headphones can be easily calculated from the maximum amplifier output voltage. For example, for a headphone with a sensitivity of 100 dB (SPL)/V, an amplifier with an output of 1 root mean square (RMS) voltage produces a maximum volume of 100 dB.
Over-ear and on-ear headphones effectively block out outside sounds, allowing you to hear your music or whatever else you're listening to crisply and without distraction. Over-ear headphones are sometimes known as full-size headphones because they completely envelop the wearer's ear. This results in what's known as passive noise reduction, which makes these some of the most-preferred headphones available. The only drawback is that your ears and the skin around your ears can get warm and sweaty. These are usually the heaviest type of headphones.
×