We use a commercially-available Bluetooth high-def interface with an S/PDIF output to test the Bluetooth output of four flagship phones. This way, we’re able to record test signal output and compare the datasets with our in-house analysis software. We kicked the tires on a 96kHz/24-bit test file to see how Bluetooth handled high-bitrate music, as well as normal 44.1kHz/16-bit files to see how each codec treated CD-quality streaming audio. We then measured the recorded sample against the original file. We used both lograrithmic sine sweeps, and complex signals like square waves in order to provide a more realistic set of tests for how people actually use Bluetooth headphones.
If you just want to block out sound without active noise cancellation, good over-ear headphones will naturally do that to some extent. This is called noise isolation, and it simply works from the earcups forming a good seal over your ears to prevent outside noise from getting in. It's not as effective, but it's less expensive than active noise cancellation and doesn't require power.
Case in point: the Koss PortaPro headphones first hit the market in 1984 and have become such a favorite with audiophiles that the company leaves the design (and the price tag) untouched. You can still pick one up for less than $50, and they come with a lifetime warranty, no receipt necessary. Check out our favorite budget headphones for more selections.
I’m a former Mixer and DJ and I’d highly recommend the Beyer T1 for mixing. It is not absolutely flat, but it is an all around proper Audio Technicians Headphone. For flat response, I might eyeball the HD800 but the low end might not be the best if you are often mixing tracks with solid low ends. Flat might not always be the best option ( my opinion ). If you need to mix heavy bass tracks, it is better to have a headphone that responds better to low end EQ and is generally accepted as a more well rounded headphone.
The impedance of headphones is of concern because of the output limitations of amplifiers. A modern pair of headphones is driven by an amplifier, with lower impedance headphones presenting a larger load. Amplifiers are not ideal; they also have some output impedance that limits the amount of power they can provide. To ensure an even frequency response, adequate damping factor, and undistorted sound, an amplifier should have an output impedance less than 1/8 that of the headphones it is driving (and ideally, as low as possible). If output impedance is large compared to the impedance of the headphones, significantly higher distortion is present.[11] Therefore, lower impedance headphones tend to be louder and more efficient, but also demand a more capable amplifier. Higher impedance headphones are more tolerant of amplifier limitations, but produce less volume for a given output level.
I have heard only the 8.35D, which are slightly dark (tilted toward the low end a little bit). But the 8.35D is very smooth and linear overall, excellent for many genres if not all. With the SRH840 you should expect a big hump in the upper bass – not ideal for monitoring. The KRK 8400 seems like the most accurate of all which is ideal for monitoring, but that’s based on a bunch of reviews, and not all of them agree 100 percent.
The Bose QuietComfort 25 were released in 2015 and you can still buy them today. They are kind of like a wired version of the Bose QuietComfort 35. They have a slightly dated look, and boast almost as good levels of active noise-cancellation and sound quality as Bose’s QuietComfort 35. The important thing to remember is that even though these are wired headphones, they still need to be charged so you can turn on the active noise cancellation. Otherwise, they just work as normal over-ear headphones.

A balanced armature is a sound transducer design primarily intended to increase the electrical efficiency of the element by eliminating the stress on the diaphragm characteristic of many other magnetic transducer systems. As shown schematically in the first diagram, it consists of a moving magnetic armature that is pivoted so it can move in the field of the permanent magnet. When precisely centered in the magnetic field there is no net force on the armature, hence the term 'balanced.' As illustrated in the second diagram, when there is electric current through the coil, it magnetizes the armature one way or the other, causing it to rotate slightly one way or the other about the pivot thus moving the diaphragm to make sound.
Over-ear and on-ear headphones effectively block out outside sounds, allowing you to hear your music or whatever else you're listening to crisply and without distraction. Over-ear headphones are sometimes known as full-size headphones because they completely envelop the wearer's ear. This results in what's known as passive noise reduction, which makes these some of the most-preferred headphones available. The only drawback is that your ears and the skin around your ears can get warm and sweaty. These are usually the heaviest type of headphones.
×