That depends on what you’re using them for and how much you’re willing to spend. At the high-end, over-ear and in-ear headphones can both perform fantastically. For those of us not willing to spend thousands on headphones, over-ear headphones typically offer better bass response and a bigger soundstage, but in-ear headphones are significantly more portable and convenient — especially wireless earbuds.
Those who buy either of these headphones are in for a treat. Our reviewer didn’t hold back in their assessment of these cans’ ability to fully realize every detail of a recording, noting their “warm and rigid bass, a midrange that dips close to the ruddy colors of analog tape saturation (without sacrificing an ounce of detail), and a laser tight response up top that helps illuminate vivid clarity and granular instrumental texture across the board.”
The moving coil driver, more commonly referred to as a "dynamic" driver is the most common type used in headphones. It consists of a stationary magnet element affixed to the frame of the headphone, which sets up a static magnetic field. The magnet in headphones is typically composed of ferrite or neodymium. A voice coil, a light coil of wire, is suspended in the magnetic field of the magnet, attached to a diaphragm, typically fabricated from lightweight, high-stiffness-to-mass-ratio cellulose, polymer, carbon material, paper or the like. When the varying current of an audio signal is passed through the coil, it creates a varying magnetic field that reacts against the static magnetic field, exerting a varying force on the coil causing it and the attached diaphragm to vibrate. The vibrating diaphragm pushes on the air to produce sound waves.
Electrostatic drivers consist of a thin, electrically charged diaphragm, typically a coated PET film membrane, suspended between two perforated metal plates (electrodes). The electrical sound signal is applied to the electrodes creating an electrical field; depending on the polarity of this field, the diaphragm is drawn towards one of the plates. Air is forced through the perforations; combined with a continuously changing electrical signal driving the membrane, a sound wave is generated. Electrostatic headphones are usually more expensive than moving-coil ones, and are comparatively uncommon. In addition, a special amplifier is required to amplify the signal to deflect the membrane, which often requires electrical potentials in the range of 100 to 1000 volts.
The Astro Gaming A50 emerged in 2012 as the wireless follow-up to the excellent A40. Seven years later and four generations on, they remain the gold standard for gaming audio. With an ability to faithfully reproduce 7.1 channel surround sound through just two earcups, gamers will get critical 3D audio for all of their favorite console titles whether it’s from an Xbox One or a PlayStation 4. Wireless audio can lead to an unacceptable amount of lag, which often sends gamers in search of wired models, but here too, the A50 manage to beat expectations.
AAC has some advantages when it comes to latency, but we recommend avoiding this if you care about audio quality. We found high levels of noise and lower than average frequency cutoffs—both unacceptable to audiophiles and younger listeners. Though the sound isn’t as bad as some may make it out to be, the shortcomings are noticeable to the human ear at normal listening volumes.
One thing I suggest to prospective customers for a specific headphone, if I have that headphone on hand, is for them to suggest 2 or 3 music tracks by a particular artist and composer that I can sample on that headphone, not so much for me to suggest how it sounds, but mostly to check if that headphone has any real sonic issues with that music. For example, a headphone that’s ideal for classical and acoustic music might sound too harsh with metal and industrial goth.
Preferences for the length of headphone cables vary for portable users, especially depending on where you prefer to wear your device: a backpack or a pants pocket necessitates a longer cable, while you'll opt for a short one when wearing a player on a neck lavalier or an armband. But a cable length at either extreme need not be a fatal flaw: extension cables can lengthen those that are too short, and cable wraps can tighten up ones that are too long.
Transducer technologies employed much less commonly for headphones include the Heil Air Motion Transformer (AMT); Piezoelectric film; Ribbon planar magnetic; Magnetostriction and Plasma-ionisation. The first Heil AMT headphone was marketed by ESS Laboratories and was essentially an ESS AMT tweeter from one of the company's speakers being driven at full range. Since the turn of the century, only Precide of Switzerland have manufactured an AMT headphone. Piezoelectric film headphones were first developed by Pioneer, their two models used a flat sheet of film that limited the maximum volume of air movement. Currently, TakeT produces a piezoelectric film headphone shaped similarly to an AMT transducer but, which like the Precide driver, has a variation in the size of transducer folds over the diaphragm. It additionally incorporates a two way design by its inclusion of a dedicated tweeter/supertweeter panel. The folded shape of a diaphragm allows a transducer with a larger surface area to fit within smaller space constraints. This increases the total volume of air that can be moved on each excursion of the transducer given that radiating area.
In-ear headphones are like earbuds but are an upgrade to them. These headphones fit into the wearer's ear canal and stay in place with the use of foam or rubber tips. These tips are available in custom sizes so they can fit each individual wearer. When a proper fit's achieved, in-ear headphones reduce outside noise and deliver sound quality at about the same level as over-ear and on-ear headphones.
×