At the heart of the WH-1000xM3 is outstanding wireless sound. Sony’s LDAC technology delivers a wireless signal at what the company claims is three times the quality of standard Bluetooth streaming, and the headphones also support the latest aptX HD codec (with supported devices). The 1000xM3 even “upscale” wireless music from high-resolution audio devices using a special chip, helping to make music sound dynamic and beautiful, with authoritative bass and clear treble response held together by a well-rounded midrange.

This is better than I thought it would be. Worst case is the T51p won’t have the excitement of the more “V”-shaped headphone sounds, but you’ll hear more of what’s actually in the recording. The more neutral headphones are most often a little bright (that’s what most users say), and can irritate on electronic and improvised music, but the T51p didn’t show any of that with these 3 tracks.

We run every pair through a rigorous testing process over several days or weeks. That includes playing them in all sorts of scenarios — be it on a bus, in the listening room, or at the office — and playing back from a wide array of sources. We know most people use their headphones with a smartphone, often with lower-quality MP3 resolution tracks, so we do, too.
The company is well known for bringing noise-canceling headphones to the general public — the QuietComfort Acoustic Noise Cancelling headphones were released in 2000 — and since then, it’s only continued to churn out industry-leading noise-canceling headphones. Its most recent iteration, the Noise Cancelling Headphones 700, might just be the best noise-canceling headphones, ever.
Ok, it’s been a month and a lot of new experience. I’ve auditoned ATH M-50 (clamp’s too tight; they sweat my ears just from few minutes of exposure) and Senn HD 600 (the velour pad is amazingly comfortable & size is ok). So, long story short, now I can refine my search to: circumaural&non-pleather/foam pads, which brought me to Senn HD 439 (cloth) & 518 (velour).
The impedance of headphones is of concern because of the output limitations of amplifiers. A modern pair of headphones is driven by an amplifier, with lower impedance headphones presenting a larger load. Amplifiers are not ideal; they also have some output impedance that limits the amount of power they can provide. To ensure an even frequency response, adequate damping factor, and undistorted sound, an amplifier should have an output impedance less than 1/8 that of the headphones it is driving (and ideally, as low as possible). If output impedance is large compared to the impedance of the headphones, significantly higher distortion is present.[11] Therefore, lower impedance headphones tend to be louder and more efficient, but also demand a more capable amplifier. Higher impedance headphones are more tolerant of amplifier limitations, but produce less volume for a given output level.
64 audio A&K AAW ALO Audio Astell Astell & Kern Astell 'n Kern AstellKern astellnkern Audez'e Audioquest Audio Technica Beyerdynamic Burson canjam Cayin Chord Chord Electronics CypherLabs Earsonics Effect Audio Empire Ears Fiio Flare Audio giveaway Grado Hifiman Ibasso JH Audio Jomo Jomo Audio Meze Noble Audio Nuforce picture Sunday Picture Wednesday plusSound Review Sennheiser Sony STAX The Fav album of Ultimate Ears Watch it Wednesday Wayback Wednesday
Impedance: Generally speaking, the lower the headphones' electrical impedance (aka resistance), the easier it is to get higher volume. But here again, the low impedance is no guarantee of high volume capability; other factors can still limit loudness potential. Since many MP3 players have feeble power output -- the iPod is a notable exception -- smart shoppers should check the loudness before purchasing any pair of headphones. To be sure, listen with your player.
The usual way of limiting sound volume on devices driving headphones is by limiting output power. This has the additional undesirable effect of being dependent of the efficiency of the headphones; a device producing the maximum allowed power may not produce adequate volume when paired with low-efficiency, high-impedance equipment, while the same amount of power can reach dangerous levels with very efficient earphones.

hi? i want to ask a question. Im a complete newbie on the audiphilic side so i red on a site that the more the impedance is higher a headphone amp is requierd and less the impedance a headphone amp is not that much requierd cause the headphones with less impedance are made for portable players. Now let me get to the point im using cheap headphones the philips sbc hp250 they are old about 5 years and sound ok but i want to replace them so i use them mostly for listening to hours of music and i am also a musician so would it make a diference if i would buy a behringer headphone amp http://www.amazon.com/Behringer-HA400-4-Channel-Stereo-Headphone/dp/B000KIPT30/ref=sr_1_6?ie=UTF8&qid=1379715994&sr=8-6&keywords=behringer+amplifier and amplify those headphones would they play better cause now im having them plugged on a intergrated via vinyl soundcard http://www.via.com.tw/en/products/audio/codecs/vt1708s/. and they sound shitty on full volume. I am considering to buy new full size headphones and im willing to give max 80 euros for them so for the start i just want them to be loud but i want a clear sound at high volume levels. To be more specific i want a clear sound that is balanced in the lows mids and highs but not distorted and the lows should not be too much overpowered. I was sniffing around your site and found some sennheiser hd 202 ii they are not even close to 80 euros but i heard they sound great would they be better than these philips headphones and what other alternatives would you suggest me for max 80 euros


Released in 2017, the Bose SoundWear Companion is a different kind of wireless headset. It doesn’t have any earcups or earbuds, but instead it sits around your neck adn has speakers that shoot sound up towards your ear — it’s essentially a portable speaker that sits around your neck. It’s water-resistant, so you can technically work out while wearing it, but it’s really designed for the person who works at home. It’s comfortable enough to wear for lengthy periods of time, but it also has excellent built-in microphones and works great as a speakerphone.
Garbage in = Garbage out (GIGO) is a popular phrase used to emphasize the importance of a good source. This can be the soundcard in your laptop, the quality of your portable audio player, or the CD player you’re using for music listening. Those fall into the “Source” category. The better your source is, the better the sound will be at the headphone end. This is why we are seeing more and more audiophile digital audio players (audiophile DAPs). They are expensive but they sound good.
They’re among the best-performing wireless home/studio-style headphones in our ratings, and though the price fluctuates, you can often find them for as little as $150. That’s less than half of what you’d pay for some comparable models. If you want over-ear headphones with the convenience of Bluetooth, this pair is a steal. It comes with a detachable audio cable so that you can use your headphones without draining the battery, and the ear cups fold in for easy storage and travel.
The tech-speak description for this type of headphone is "circumaural," which includes any headphones with earcups that fully enclose your ears. Because of their size and their acoustic isolation, full-size headphones are often considered to be better-suited to home use rather than as a portable option, but the recent popularity of full-size, noise-canceling Beats headphones are challenging the rule.
The QuietComfort 30s are Bose’s wireless in-ear headphones with active noise cancellation, and they’ve set the bar for the category since they were released in 2016. The QuietComfort 30s utilize the same StayHear+ tips as all Bose’s other in-ear headphones and they use the same app as the company’s other QuietComfort headphones. The one caveat is that the QuietComfort 30s are a neckband-style of wireless headphone, so they’re fairly heavy and probably best served for office settings.
The problem is made even worse by the fact that Android phones can’t handle AAC in a method that approaches Apple’s performance with the codec. Consequently, we will no longer be recommending AAC-only headsets here at SoundGuys, as the experience is that broken from source to source. The results are crappier and noisier than the other codecs by a longshot.

The rule that I use is that the bigger the size of the headphone, the bigger the need for amplification. Of course factors like driver sensitivity and impedance will matter, but the general rule of thumb is, use a dedicated headphone amplifier for a full size headphone. Even a portable amplifier can be enough, depending on the type of the headphones.

Those who buy either of these headphones are in for a treat. Our reviewer didn’t hold back in their assessment of these cans’ ability to fully realize every detail of a recording, noting their “warm and rigid bass, a midrange that dips close to the ruddy colors of analog tape saturation (without sacrificing an ounce of detail), and a laser tight response up top that helps illuminate vivid clarity and granular instrumental texture across the board.”


The Bose QuietComfort 25 were released in 2015 and you can still buy them today. They are kind of like a wired version of the Bose QuietComfort 35. They have a slightly dated look, and boast almost as good levels of active noise-cancellation and sound quality as Bose’s QuietComfort 35. The important thing to remember is that even though these are wired headphones, they still need to be charged so you can turn on the active noise cancellation. Otherwise, they just work as normal over-ear headphones.
We’re totally convinced the Sony WH-1000xM3 will be the best pick for most people, but if you’re looking for some alternatives, we have you covered there, too. We identified seven other models that are more than worthy of your consideration, each with their own specific strengths, whether it’s for use during a workout — or merely to keep you from giving your credit card too much of a workout.
As the name gives away, these have an on-ear design instead of the over-ear design of most of Bose’s other offerings. The trade-off is that the On-Ear Wireless Headphones won’t be able to block out ambient noises as well, but some people might find them more comfortable. Plus they’re well cheaper than most other Bose wireless headphones. It should be noted that many reviewers, including Sound Guys, have praised the sound quality of these headphones.
While iPhone users can expect that their phones are missing essential parts to look good, AAC is one of those codecs that maybe cut a few too many bits out of its data transmission. By using an aggressive psychoacoustic model of compression, AAC seeks to cut data where you wouldn’t normally be able to hear it anyway—but it gets a little too aggressive at times.
Music keeps me energized all day (and into the night) at work — 70% electronica/dance/DNB, 20% rock, 5% hip hip and 5% other/classical — but I’m tired of low-quality sound and I’m ready to put my money where my ears are.  I want to buy a USB DAC + Headphone amp, buy headphones (or, per your recommendation, to buy 2 pair) to complement the amp and my choice of music, and get great desktop sound for around $350.

One thing I suggest to prospective customers for a specific headphone, if I have that headphone on hand, is for them to suggest 2 or 3 music tracks by a particular artist and composer that I can sample on that headphone, not so much for me to suggest how it sounds, but mostly to check if that headphone has any real sonic issues with that music. For example, a headphone that’s ideal for classical and acoustic music might sound too harsh with metal and industrial goth.
As the name gives away, these have an on-ear design instead of the over-ear design of most of Bose’s other offerings. The trade-off is that the On-Ear Wireless Headphones won’t be able to block out ambient noises as well, but some people might find them more comfortable. Plus they’re well cheaper than most other Bose wireless headphones. It should be noted that many reviewers, including Sound Guys, have praised the sound quality of these headphones.
The Soundsport Free, released in the fall of 2017, are Bose’s first truly wireless earbuds. They utilize the same StayHear+ Sport tips as the company’s other in-ear headphones, making them naturally more sweat-resistant and more secure than AirPods. They work with the Bose Connect app, which is pretty basic but does have a “Find My Buds” feature that, when enabled, can help you find your earbuds should you misplace them.
Hearing risk from headphones' use also applies to workers who must wear electronic or communication headsets as part of their daily job (i.e., pilots, call center and dispatch operators, sound engineers, firefighters, etc.) and hearing damage depends on the exposure time. The National Institute for Occupational Safety and Health (NIOSH) recommends sound exposure not exceed 85 dB(A) over 8 hour work day as a time-weighted average.[35] NIOSH uses the 3-dB exchange rate often referred to as "time-intensity tradeoff" which means if sound exposure level is increased by 3 decibels, the duration of exposure should be cut in half. NIOSH published several documents targeted at protecting the hearing of workers who must wear communication headsets such as call center operators,[36] firefighters,[37] and musicians and sound engineers.[38]
Transducer technologies employed much less commonly for headphones include the Heil Air Motion Transformer (AMT); Piezoelectric film; Ribbon planar magnetic; Magnetostriction and Plasma-ionisation. The first Heil AMT headphone was marketed by ESS Laboratories and was essentially an ESS AMT tweeter from one of the company's speakers being driven at full range. Since the turn of the century, only Precide of Switzerland have manufactured an AMT headphone. Piezoelectric film headphones were first developed by Pioneer, their two models used a flat sheet of film that limited the maximum volume of air movement. Currently, TakeT produces a piezoelectric film headphone shaped similarly to an AMT transducer but, which like the Precide driver, has a variation in the size of transducer folds over the diaphragm. It additionally incorporates a two way design by its inclusion of a dedicated tweeter/supertweeter panel. The folded shape of a diaphragm allows a transducer with a larger surface area to fit within smaller space constraints. This increases the total volume of air that can be moved on each excursion of the transducer given that radiating area.

I see, yes, but that should serve as an important lesson – the soundstage is not real in the same sense as actual tones, bass, treble, whatever. Soundstage is a perception that’s based on many factors, and here’s a challenge for you: You should be able to find some music tracks that have better soundstage on one headphone, and other tracks that will be better on the other headphone. Most of the time it will be just one way, but when a closed headphone beats an open headphone, I expect the open headphone will still show an advantage on some tracks. Your hearing perception could be tricked by simple things like a recess or emphasis in certain frequency ranges, or even phase shift when more than one driver is in the cup.


We were frankly surprised at just how good the AirPods Pro turned out to be. The noise cancellation is on-par with Sony’s WH-1000XM3, which is saying a lot. The new in-ear design is both comfortable and secure. And amazingly, they sound way better than Apple’s previous version. We would often bemoan the fact that the AirPods didn’t sound very good, especially when compared to the plethora of decent true wireless options for the same or less money.
Earphones are very small headphones that are fitted directly in the outer ear, facing but not inserted in the ear canal. Earphones are portable and convenient, but many people consider them uncomfortable.[16] They provide hardly any acoustic isolation and leave room for ambient noise to seep in; users may turn up the volume dangerously high to compensate, at the risk of causing hearing loss.[16][17] On the other hand, they let the user be better aware of their surroundings. Since the early days of the transistor radio, earphones have commonly been bundled with personal music devices. They are sold at times with foam pads for comfort. (The use of the term earbuds, which has been around since at least 1984, did not hit its peak until after 2001, with the success of Apple's MP3 player.[18])
×