Just a few hours of burn-in today – I don’t expect much change with Tesla-quality drivers etc. The treble is recessed almost as much as the Philips M1 I had, kind-of a worst-case scenario. So I took out my most minimal non-peaky non-bright non-sibilant headphone – the B&O H6, and even though it doesn’t sound the same as the T51p because of the H6’s “light” midrange, I wanted to get a sense of how much the T51p was recessed below a very minimal treble. My Foobar2000 settings were +2 at 2.5, +4 at 3.5, +2 at 5, +4 at 7, +6 at 10, 14, and 20 khz. Normally I wouldn’t do the dip at 5 khz, but the T51p has a nasty 10 db peak around 5 khz, which makes it difficult for portable use without a customizable equalizer. Without a treble boost it sounds very boomy as well as muffled. I can understand Beyer going to a darker sound with more bass – in fact I thought it was a move in the right direction. But they need to cut that (resonant?) peak around 5 khz. I compared to several other headphones and none of those were anything like that.
Dale: There are so many types of amplifiers (and DAC’s with amplifiers) that there is no shortcut for studying all of the options, unless you settle for the most generic approach. Important things to consider are power – if you don’t have enough power for your headphone and the dynamics in the music, clipping will result. Sometimes the clipping is “soft” and not readily noticed, but eventually you would discover that much of the detail goes missing or gets veiled with limited dynamics. Another consideration is whether to use a DAC, which may be a separate DAC or built into the same enclosure as the amp. Most DACs will improve the sound over the DACs that are built into computers, but when a DAC is available to replace the DAC built into most cellphones and low to mid-priced music players, you can usually expect a much greater improvement.

I tend to regard the M50 as the minimum for hi-fi listening with no apologies for limitations. But if you have to go cheaper than the usual $125 USD for the M50, the B&O Form2 with a simple bass boost gives a real hi-fi sound, and it should be available for about $100. The Beyer DTX-501P (similar to soundmagic P30) is good for $100, but needs a slight treble boost. The LSTN Fillmore with wood cups is somewhat colored, but still a good listen and good for $100. Below $100 are the Sennheiser PX series – not hi-fi by any means. There are several good IEMs below $100, and Apple Earpods with a Dirac or Accudio Pro player are very hi-fi, and cheap.

Transducer technologies employed much less commonly for headphones include the Heil Air Motion Transformer (AMT); Piezoelectric film; Ribbon planar magnetic; Magnetostriction and Plasma-ionisation. The first Heil AMT headphone was marketed by ESS Laboratories and was essentially an ESS AMT tweeter from one of the company's speakers being driven at full range. Since the turn of the century, only Precide of Switzerland have manufactured an AMT headphone. Piezoelectric film headphones were first developed by Pioneer, their two models used a flat sheet of film that limited the maximum volume of air movement. Currently, TakeT produces a piezoelectric film headphone shaped similarly to an AMT transducer but, which like the Precide driver, has a variation in the size of transducer folds over the diaphragm. It additionally incorporates a two way design by its inclusion of a dedicated tweeter/supertweeter panel. The folded shape of a diaphragm allows a transducer with a larger surface area to fit within smaller space constraints. This increases the total volume of air that can be moved on each excursion of the transducer given that radiating area.


The thermoacoustic effect generates sound from the audio frequency Joule heating of the conductor, an effect that is not magnetic and does not vibrate the speaker. In 2013 a carbon nanotube thin-yarn earphone based on the thermoacoustic mechanism was demonstrated by a research group in Tsinghua University.[22] The as-produced CNT thin yarn earphone has a working element called CNT thin yarn thermoacoustic chip. Such a chip is composed of a layer of CNT thin yarn array supported by the silicon wafer, and periodic grooves with certain depth are made on the wafer by micro-fabrication methods to suppress the heat leakage from the CNT yarn to the substrate.[citation needed]
With a Lightning a USB-C headphone you plug the headphone directly into the Lightning port (on Apple devices) or USB-C port (on Android devices). A standard headphone plug is an analog connection while this creates a direct digital connection. The headphones are powered by your phone (they use only a little bit of battery power) and have an integrated DAC (digital-to-analog converter) that's usually superior to the DAC in your phone.
Although some headphones available are wired, many more are available that are wireless, and use Bluetooth to enable your music to be heard, even if the stereo or other device is several feet or even a few rooms away. Wired headphones deliver superior sound quality to wireless and Bluetooth because there's no chance of picking up interference from other devices, which sometimes happens with wireless headphones. In addition, wired headphones have no batteries to power them, so there's no chance of interruption should the batteries wear out.
×