Headphones can prevent other people from hearing the sound, either for privacy or to prevent disturbing others, as in listening in a public library. They can also provide a level of sound fidelity greater than loudspeakers of similar cost. Part of their ability to do so comes from the lack of any need to perform room correction treatments with headphones. High-quality headphones can have an extremely flat low-frequency response down to 20 Hz within 3 dB. While a loudspeaker must use a relatively large (often 15" or 18") speaker driver to reproduce low frequencies, headphones can accurately reproduce bass and sub-bass frequencies with speaker drivers only 40-50 millimeters wide (or much smaller, as is the case with in-ear monitor headphones). Headphones' impressive low-frequency performance is possible because they are so much closer to the ear that they only need to move relatively small volumes of air.
Their combination of dual balanced-armature drivers matched with a dynamic driver to pump up the lower end are kind of engineering normally found on products that cost more than double the price of the 1Mores. Even the smaller details are very well ironed out, such as Kevlar-wrapped cables that increase resistance to wear while simultaneously reducing tangles.
A. Near-field communication, better known as NFC, is a wireless connectivity protocol similar to Bluetooth. NFC uses less power than Bluetooth and is faster when pairing devices, but it only has a range of about four inches. Some headphones use NFC technology to drive the process of pairing headphones with smartphones, but because of the range, it’s not used to transmit sound. While both Android phones and iPhones include NFC chips, it’s not accessible in Apple devices, so if you want a pair of headphones with NFC, you’ll need to own an Android phone to take advantage of the faster pairing.
An electret driver functions along the same electromechanical means as an electrostatic driver. However the electret driver has a permanent charge built into it, whereas electrostatics have the charge applied to the driver by an external generator. Electret and electrostatic headphones are relatively uncommon. Original electrets were also typically cheaper and lower in technical capability and fidelity than electrostatics. Patent applications from 2009-2013 have been approved that show by using different materials, i.e. a "Fluorinated cyclic olefin electret film", Frequency response chart readings can reach 50 kHz at 100db. When these new improved electrets are combined with a traditional dome headphone driver, headphones can be produced that are recognised by the Japan Audio Society as worthy of joining the Hi Res Audio program. US patents 8,559,660 B2. 7,732,547 B2.7,879,446 B2.7,498,699 B2.
Will Greenwald has been covering consumer technology for a decade, and has served on the editorial staffs of CNET.com, Sound & Vision, and Maximum PC. His work and analysis has been seen in GamePro, Tested.com, Geek.com, and several other publications. He currently covers consumer electronics in the PC Labs as the in-house home entertainment expert, reviewing TVs, media hubs, speakers, headphones, and gaming accessories. Will is also an ISF Level II-certified TV calibrator, which ensures the thoroughness and accuracy of all PCMag TV reviews.
hi? i want to ask a question. Im a complete newbie on the audiphilic side so i red on a site that the more the impedance is higher a headphone amp is requierd and less the impedance a headphone amp is not that much requierd cause the headphones with less impedance are made for portable players. Now let me get to the point im using cheap headphones the philips sbc hp250 they are old about 5 years and sound ok but i want to replace them so i use them mostly for listening to hours of music and i am also a musician so would it make a diference if i would buy a behringer headphone amp http://www.amazon.com/Behringer-HA400-4-Channel-Stereo-Headphone/dp/B000KIPT30/ref=sr_1_6?ie=UTF8&qid=1379715994&sr=8-6&keywords=behringer+amplifier and amplify those headphones would they play better cause now im having them plugged on a intergrated via vinyl soundcard http://www.via.com.tw/en/products/audio/codecs/vt1708s/. and they sound shitty on full volume. I am considering to buy new full size headphones and im willing to give max 80 euros for them so for the start i just want them to be loud but i want a clear sound at high volume levels. To be more specific i want a clear sound that is balanced in the lows mids and highs but not distorted and the lows should not be too much overpowered. I was sniffing around your site and found some sennheiser hd 202 ii they are not even close to 80 euros but i heard they sound great would they be better than these philips headphones and what other alternatives would you suggest me for max 80 euros

Transducer technologies employed much less commonly for headphones include the Heil Air Motion Transformer (AMT); Piezoelectric film; Ribbon planar magnetic; Magnetostriction and Plasma-ionisation. The first Heil AMT headphone was marketed by ESS Laboratories and was essentially an ESS AMT tweeter from one of the company's speakers being driven at full range. Since the turn of the century, only Precide of Switzerland have manufactured an AMT headphone. Piezoelectric film headphones were first developed by Pioneer, their two models used a flat sheet of film that limited the maximum volume of air movement. Currently, TakeT produces a piezoelectric film headphone shaped similarly to an AMT transducer but, which like the Precide driver, has a variation in the size of transducer folds over the diaphragm. It additionally incorporates a two way design by its inclusion of a dedicated tweeter/supertweeter panel. The folded shape of a diaphragm allows a transducer with a larger surface area to fit within smaller space constraints. This increases the total volume of air that can be moved on each excursion of the transducer given that radiating area.

Restock! Check out this 60 Watt Digital Soldering Station! This 60W digital soldering station takes the guesswork out of the temperature equation. -Temperature dial allows for precise settings ranging from 302ºF to 842ºF (150ºC to 450ºC). -Digital LCD display shows actual temperature and setting. -Temperature display toggles between Fahrenheit and Celsius. -3 temperature presets for common settings: 392ºF (200ºC), 680ºF (360ºC) and 788ºF (420ºC). -Detachable iron with pencil-style tip. -Includes cradle stand. -Works with lead-free, rosin-core, lead-based or silver-bearing solder. -Be prepared for any job, and stock up on a variety of solder, including rosin-core, lead-free, silver-bearing, clear flux and more.

×