That depends on what you’re using them for and how much you’re willing to spend. At the high-end, over-ear and in-ear headphones can both perform fantastically. For those of us not willing to spend thousands on headphones, over-ear headphones typically offer better bass response and a bigger soundstage, but in-ear headphones are significantly more portable and convenient — especially wireless earbuds.
A. It depends. Noise-cancelling headphones use active technology to play unique frequencies that block outside noises, and depending on which model you buy, the battery can last anywhere from 15 to 40 hours. If you’re using a set of wireless headphones, the battery will be used for both noise cancellation and wireless connectivity, so expect the battery to deplete faster if you’re using both.
Interestingly, yesterday I was comparing my beyer 770 with my AT ath30 and then I realised how important it is also the soundstage, the good separation of instruments … finally I have decided I want to take this into account as well, and not only the issue of bass, midrange and treble … Since, in my opinion lack of bass we can try to fix it, but lack of soundstage is impossible, right?
Headphones (or head-phones in the early days of telephony and radio) traditionally refer to a pair of small loudspeaker drivers worn on or around the head over a user's ears. They are electroacoustic transducers, which convert an electrical signal to a corresponding sound. Headphones let a single user listen to an audio source privately, in contrast to a loudspeaker, which emits sound into the open air for anyone nearby to hear. Headphones are also known as earspeakers, earphones[1] or, colloquially, cans.[2] Circumaural ('around the ear') and supra-aural ('over the ear') headphones use a band over the top of the head to hold the speakers in place. Another type, known as earbuds or earpieces[1] consist of individual units that plug into the user's ear canal. A third type are bone conduction headphones, which typically wrap around the back of the head and rest in front of the ear canal, leaving the ear canal open. In the context of telecommunication, a headset is a combination of headphone and microphone.
Of the tested codecs we met, aptX and aptX HD fared the best out of all our candidates. While that may seem strange to say, on the whole their results were right where they needed to be in order to stand in for a wire for commuters, and listeners over 40. You’d really only run into issues at high volumes (90+dB), so while aptX isn’t quite able to keep up with CD quality, aptX HD is able to get extremely close to the mark with a little processing creativeness. Both codecs fall short in the highest frequencies a human could potentially hear, but the vast majority of people can’t hear sounds over 18kHz anyway.

Dale: There are so many types of amplifiers (and DAC’s with amplifiers) that there is no shortcut for studying all of the options, unless you settle for the most generic approach. Important things to consider are power – if you don’t have enough power for your headphone and the dynamics in the music, clipping will result. Sometimes the clipping is “soft” and not readily noticed, but eventually you would discover that much of the detail goes missing or gets veiled with limited dynamics. Another consideration is whether to use a DAC, which may be a separate DAC or built into the same enclosure as the amp. Most DACs will improve the sound over the DACs that are built into computers, but when a DAC is available to replace the DAC built into most cellphones and low to mid-priced music players, you can usually expect a much greater improvement.
The impedance of headphones is of concern because of the output limitations of amplifiers. A modern pair of headphones is driven by an amplifier, with lower impedance headphones presenting a larger load. Amplifiers are not ideal; they also have some output impedance that limits the amount of power they can provide. To ensure an even frequency response, adequate damping factor, and undistorted sound, an amplifier should have an output impedance less than 1/8 that of the headphones it is driving (and ideally, as low as possible). If output impedance is large compared to the impedance of the headphones, significantly higher distortion is present.[11] Therefore, lower impedance headphones tend to be louder and more efficient, but also demand a more capable amplifier. Higher impedance headphones are more tolerant of amplifier limitations, but produce less volume for a given output level.

While iPhone users can expect that their phones are missing essential parts to look good, AAC is one of those codecs that maybe cut a few too many bits out of its data transmission. By using an aggressive psychoacoustic model of compression, AAC seeks to cut data where you wouldn’t normally be able to hear it anyway—but it gets a little too aggressive at times.
Wired headphones are attached to an audio source by a cable. The most common connectors are 6.35 mm (¼″) and 3.5 mm phone connectors. The larger 6.35 mm connector is more common on fixed location home or professional equipment. The 3.5 mm connector remains the most widely used connector for portable application today. Adapters are available for converting between 6.35 mm and 3.5 mm devices.

Hey Mike, I’m a mixing Engineer looking to invest in a high end pair of headphones for when i’m forced to mix a song on the road. I already have the DT 770 pros and BEATS by dre headphones which i feel will be good enough for references. But I’m looking for a 3rd pair that really has a flat response and that is very detailed. I’m willing to spend $1,500 to $2,500. Are there any headphones you can recommend looking into. Thanks

Be sure to assess the build quality of your prospective headphones. Some earbuds and portable devices are relatively fragile, for instance. If the headphones fold up for easy storage, are the hinges robust, or will they fall apart in a month or two? Don't forget to consider that the earpads and earbuds will get extensive wear and tear over the life of the headphones.
A headset is a headphone combined with a microphone. Headsets provide the equivalent functionality of a telephone handset with hands-free operation. Among applications for headsets, besides telephone use, are aviation, theatre or television studio intercom systems, and console or PC gaming. Headsets are made with either a single-earpiece (mono) or a double-earpiece (mono to both ears or stereo). The microphone arm of headsets is either an external microphone type where the microphone is held in front of the user's mouth, or a voicetube type where the microphone is housed in the earpiece and speech reaches it by means of a hollow tube.
Alternatively, online calculators can be used.[13] Once the sensitivity per volt is known, the maximum volume for a pair of headphones can be easily calculated from the maximum amplifier output voltage. For example, for a headphone with a sensitivity of 100 dB (SPL)/V, an amplifier with an output of 1 root mean square (RMS) voltage produces a maximum volume of 100 dB.
Whether you wear headphones for your daily commute, regular workouts, or just for jamming out at home, you need a good pair that’s comfortable and can make everything sound great. Headphone tech has evolved significantly, too, so some pairs can do a lot more than just play sound. It’s not tough to find a pair that can connect to your smartphone wirelessly, or one that can keep outside commotion out.
Smaller earbud type earpieces, which plugged into the user's ear canal, were first developed for hearing aids. They became widely used with transistor radios, which commercially appeared in 1954 with the introduction of the Regency TR-1. The most popular audio device in history, the transistor radio changed listening habits, allowing people to listen to radio anywhere. The earbud uses either a moving iron driver or a piezoelectric crystal to produce sound. The 3.5 mm radio and phone connector, which is the most commonly used in portable application today, has been used at least since the Sony EFM-117J transistor radio, which was released in 1964.[9][10] Its popularity was reinforced with its use on the Walkman portable tape player in 1979.
×