Ok, it’s been a month and a lot of new experience. I’ve auditoned ATH M-50 (clamp’s too tight; they sweat my ears just from few minutes of exposure) and Senn HD 600 (the velour pad is amazingly comfortable & size is ok). So, long story short, now I can refine my search to: circumaural&non-pleather/foam pads, which brought me to Senn HD 439 (cloth) & 518 (velour).
There’s a lot of debate in the headphone world about wireless audio. Wireless standards like Bluetooth are capable of making music sound great, but because Bluetooth relies on data compression, it will never sound quite as good as a wired connection. The big question is, with the improvements in Bluetooth, can anyone tell the difference anymore between Bluetooth audio and wired audio? We’re skeptical that the difference is meaningful, so here’s our best advice: if you’re an audiophile who cares about hearing music in high fidelity, you’ll probably be better off with a set of wired headphones; if you need everything to sound great but prefer the convenience of wireless connections, go for a pair of Bluetooth headphones.
If you have a bass problem you could find a filter of some kind that cuts the low bass. Some bass controls can do that. I haven’t found a music genre that totally lacks strong bass, although “acoustic” sometimes doesn’t have strong bass. Mainly, you should make sure your system is matched properly with amp and headphone, so the different frequencies are in balance. Then you will have better luck with different music.
Headphones are available with high or low impedance (typically measured at 1 kHz). Low-impedance headphones are in the range 16 to 32 ohms and high-impedance headphones are about 100-600 ohms. As the impedance of a pair of headphones increases, more voltage (at a given current) is required to drive it, and the loudness of the headphones for a given voltage decreases. In recent years, impedance of newer headphones has generally decreased to accommodate lower voltages available on battery powered CMOS-based portable electronics. This has resulted in headphones that can be more efficiently driven by battery-powered electronics. Consequently, newer amplifiers are based on designs with relatively low output impedance.
Headphones connect to a signal source such as an audio amplifier, radio, CD player, portable media player, mobile phone, video game console, or electronic musical instrument, either directly using a cord, or using wireless technology such as Bluetooth, DECT or FM radio. The first headphones were developed in the late 19th century for use by telephone operators, to keep their hands free. Initially the audio quality was mediocre and a step forward was the invention of high fidelity headphones.[3]
We run every pair through a rigorous testing process over several days or weeks. That includes playing them in all sorts of scenarios — be it on a bus, in the listening room, or at the office — and playing back from a wide array of sources. We know most people use their headphones with a smartphone, often with lower-quality MP3 resolution tracks, so we do, too.

To be honest, I was looking at the M50 because I knew another person that had them & was very happy with them, also I read reviews online which were positive. However, I didn’t realize until now that the possibilities are pretty endless when it comes to headphones, which is why I was asking for some direction… It just sucks cause my budget is definitely limited…

Wired headphones are attached to an audio source by a cable. The most common connectors are 6.35 mm (¼″) and 3.5 mm phone connectors. The larger 6.35 mm connector is more common on fixed location home or professional equipment. The 3.5 mm connector remains the most widely used connector for portable application today. Adapters are available for converting between 6.35 mm and 3.5 mm devices.
Sensitivity is a measure of how effectively an earpiece converts an incoming electrical signal into an audible sound. It thus indicates how loud the headphones are for a given electrical drive level. It can be measured in decibels of sound pressure level per milliwatt (dB (SPL)/mW) or decibels of sound pressure level per volt (dB (SPL) / V).[12] Unfortunately, both definitions are widely used, often interchangeably. As the output voltage (but not power) of a headphone amplifier is essentially constant for most common headphones, dB/mW is often more useful if converted into dB/V using Ohm's law:
A: What you plug your headphones into can significantly affect their sound, and the quality of the amplifiers built into portable CD/MP3 players is generally awful. It's not their fault: the little guys have to power their electronics and their internal amplifier using a few puny volts. Even some of the better home AV receivers' headphone jacks offer highly variable sound quality.

Magnetostriction headphones, sometimes sold under the label Bonephones, work by vibrating against the side of head, transmitting sound via bone conduction. This is particularly helpful in situations where the ears must be unobstructed, or for people who are deaf for reasons that don't affect the nervous apparatus of hearing. Magnetostriction headphones though, are limited in their fidelity compared to conventional headphones that rely on the normal workings of the ear. Additionally, in the early 1990s, a French company called Plasmasonics tried to market a plasma-ionisation headphone. There are no known functioning examples left.
I tend to regard the M50 as the minimum for hi-fi listening with no apologies for limitations. But if you have to go cheaper than the usual $125 USD for the M50, the B&O Form2 with a simple bass boost gives a real hi-fi sound, and it should be available for about $100. The Beyer DTX-501P (similar to soundmagic P30) is good for $100, but needs a slight treble boost. The LSTN Fillmore with wood cups is somewhat colored, but still a good listen and good for $100. Below $100 are the Sennheiser PX series – not hi-fi by any means. There are several good IEMs below $100, and Apple Earpods with a Dirac or Accudio Pro player are very hi-fi, and cheap.
The Bose Frames are non-polarized sunglasses with special speakers built into each arm. The idea is that they’re designed to look like regular sunglasses, but also act as Bluetooth headphones. Since there’s no earbud that actually goes into your ears, the speakers have been engineered to shoot audio down into your ears; the neat thing is that the Bose Frames do a very good job at masking your audio so that the people around you can’t really hear what you’re listening to. They are available in two different frame styles, round (Rondo) or square (Aldo).
Released in 2017, the Bose SoundWear Companion is a different kind of wireless headset. It doesn’t have any earcups or earbuds, but instead it sits around your neck adn has speakers that shoot sound up towards your ear — it’s essentially a portable speaker that sits around your neck. It’s water-resistant, so you can technically work out while wearing it, but it’s really designed for the person who works at home. It’s comfortable enough to wear for lengthy periods of time, but it also has excellent built-in microphones and works great as a speakerphone.
Dirac is mainly for resonance (narrow band) taming and not suitable for normal EQ. Accudio is good. But since the L1 already has a strong bass emphasis, boosting mids or treble just makes the imbalance worse – i.e. the freq. response becomes more ragged and the sound more harsh. To get a smoother sound and better mids and treble, reduce the bass instead.
Fathers Day is just around the corner and we want to help you find the right gift for the amazing fathers in your life. At RadioShack of Lenoir, we have some awesome deals going on RIGHT NOW! Buy the Nebo Big Daddy Flashlight (2000 lumens) and get the Nebo Blast half off, Nebo Knives are buy one get one half off, and Nebo flipits are buy one get one 40% off. We also have some awesome Bluetooth portable speakers that can be taken to the lake, bonfire, or the beach. Also, come by and enter your father to win a Nebo glow light along with a Nebo cup! We hope to see you soon!