Although modern headphones have been particularly widely sold and used for listening to stereo recordings since the release of the Walkman, there is subjective debate regarding the nature of their reproduction of stereo sound. Stereo recordings represent the position of horizontal depth cues (stereo separation) via volume and phase differences of the sound in question between the two channels. When the sounds from two speakers mix, they create the phase difference the brain uses to locate direction. Through most headphones, because the right and left channels do not combine in this manner, the illusion of the phantom center can be perceived as lost. Hard panned sounds are also heard only in one ear rather than from one side.
Released in 2015, the SoundLink Around-Ear II are Bose’s wireless over-ear headphones that don’t have active noise cancellation. They’re lighter and slightly more travel-friendly than a lot of the company’s other offerings, and they could sound quality at the forefront. At the time, the big selling point for the SoundLink Around-Ear II was their sound quality — Bose claimed that they sounded as good as wired headphones, which admittedly doesn’t hold up in 2019 (streaming and Bluetooth have gotten too good).
We were frankly surprised at just how good the AirPods Pro turned out to be. The noise cancellation is on-par with Sony’s WH-1000XM3, which is saying a lot. The new in-ear design is both comfortable and secure. And amazingly, they sound way better than Apple’s previous version. We would often bemoan the fact that the AirPods didn’t sound very good, especially when compared to the plethora of decent true wireless options for the same or less money.
These early headphones used moving iron drivers, with either single-ended or balanced armatures. The common single-ended type used voice coils wound around the poles of a permanent magnet, which were positioned close to a flexible steel diaphragm. The audio current through the coils varied the magnetic field of the magnet, exerting a varying force on the diaphragm, causing it to vibrate, creating sound waves. The requirement for high sensitivity meant that no damping was used, so the frequency response of the diaphragm had large peaks due to resonance, resulting in poor sound quality. These early models lacked padding, and were often uncomfortable to wear for long periods. Their impedance varied; headphones used in telegraph and telephone work had an impedance of 75 ohms. Those used with early wireless radio had more turns of finer wire to increase sensitivity. Impedance of 1000 to 2000 ohms was common, which suited both crystal sets and triode receivers. Some very sensitive headphones, such as those manufactured by Brandes around 1919, were commonly used for early radio work.
If you have a bass problem you could find a filter of some kind that cuts the low bass. Some bass controls can do that. I haven’t found a music genre that totally lacks strong bass, although “acoustic” sometimes doesn’t have strong bass. Mainly, you should make sure your system is matched properly with amp and headphone, so the different frequencies are in balance. Then you will have better luck with different music.
We run every pair through a rigorous testing process over several days or weeks. That includes playing them in all sorts of scenarios — be it on a bus, in the listening room, or at the office — and playing back from a wide array of sources. We know most people use their headphones with a smartphone, often with lower-quality MP3 resolution tracks, so we do, too.
Sensitivity is a measure of how effectively an earpiece converts an incoming electrical signal into an audible sound. It thus indicates how loud the headphones are for a given electrical drive level. It can be measured in decibels of sound pressure level per milliwatt (dB (SPL)/mW) or decibels of sound pressure level per volt (dB (SPL) / V). Unfortunately, both definitions are widely used, often interchangeably. As the output voltage (but not power) of a headphone amplifier is essentially constant for most common headphones, dB/mW is often more useful if converted into dB/V using Ohm's law:
While the data signal containing Bluetooth audio is compressed, headphone and earphone manufacturers have found ways to enhance the signal to compensate for its deficiencies in a way that even audiophiles can appreciate. We've included some wireless options here, but if you're really keen on cutting the cord, check out The Best Wireless Headphones. And if you want to go completely wireless (with no cord at all connecting the two earpieces), check out The Best True Wireless Headphones—just keep in mind these are about as far from over-ear headphones as you can get.
The Bose Frames are non-polarized sunglasses with special speakers built into each arm. The idea is that they’re designed to look like regular sunglasses, but also act as Bluetooth headphones. Since there’s no earbud that actually goes into your ears, the speakers have been engineered to shoot audio down into your ears; the neat thing is that the Bose Frames do a very good job at masking your audio so that the people around you can’t really hear what you’re listening to. They are available in two different frame styles, round (Rondo) or square (Aldo).
EQ controls: Equalization, more commonly referred to as EQ, controls the different aspects of sound that come through your headphones, and some headphones come with custom apps that let you adjust the EQ in granular detail. With the right EQ controls, you can add more treble, bump up the bass, or just create a sound profile that’s suited to your tastes. If you’re into customizing how your music sounds, look for headphones that work with an EQ app.
That depends on what you’re using them for and how much you’re willing to spend. At the high-end, over-ear and in-ear headphones can both perform fantastically. For those of us not willing to spend thousands on headphones, over-ear headphones typically offer better bass response and a bigger soundstage, but in-ear headphones are significantly more portable and convenient — especially wireless earbuds.
In-ear headphones are like earbuds but are an upgrade to them. These headphones fit into the wearer's ear canal and stay in place with the use of foam or rubber tips. These tips are available in custom sizes so they can fit each individual wearer. When a proper fit's achieved, in-ear headphones reduce outside noise and deliver sound quality at about the same level as over-ear and on-ear headphones.