I think it’s fair to compare the Grados and HD598, but the M50 is very different and seems not to fit in that comparison. The DT770 is a better comparison to the M50, although the 770 is a better more expensive item. A long time ago I had a Grado 325 and a Sennheiser HD565 – very similar, very enjoyable. Today for that type of sound I might choose the Soundmagic HP100.

Those who buy either of these headphones are in for a treat. Our reviewer didn’t hold back in their assessment of these cans’ ability to fully realize every detail of a recording, noting their “warm and rigid bass, a midrange that dips close to the ruddy colors of analog tape saturation (without sacrificing an ounce of detail), and a laser tight response up top that helps illuminate vivid clarity and granular instrumental texture across the board.”
Smaller earbud type earpieces, which plugged into the user's ear canal, were first developed for hearing aids. They became widely used with transistor radios, which commercially appeared in 1954 with the introduction of the Regency TR-1. The most popular audio device in history, the transistor radio changed listening habits, allowing people to listen to radio anywhere. The earbud uses either a moving iron driver or a piezoelectric crystal to produce sound. The 3.5 mm radio and phone connector, which is the most commonly used in portable application today, has been used at least since the Sony EFM-117J transistor radio, which was released in 1964.[9][10] Its popularity was reinforced with its use on the Walkman portable tape player in 1979.
Interestingly, yesterday I was comparing my beyer 770 with my AT ath30 and then I realised how important it is also the soundstage, the good separation of instruments … finally I have decided I want to take this into account as well, and not only the issue of bass, midrange and treble … Since, in my opinion lack of bass we can try to fix it, but lack of soundstage is impossible, right?

Open back usually results in more natural sound, but they leak sound in and out. This means you probably can’t use them in a library or a plane flight since the sound of your music will leak out and disturb the people around you. You also can’t use them on loud public places since noise from the outside will disturb your music. Therefore, even though open back would give you more natural reproduction, for these reasons their use is limited to mostly at home or in the office (if you have your own space that is).
The design is not mechanically stable; a slight imbalance makes the armature stick to one pole of the magnet. A fairly stiff restoring force is required to hold the armature in the 'balance' position. Although this reduces its efficiency, this design can still produce more sound from less power than any other[clarification needed]. Popularized in the 1920s as Baldwin Mica Diaphragm radio headphones, balanced armature transducers were refined during World War II for use in military sound powered telephones. Some of these achieved astonishing electro-acoustic conversion efficiencies, in the range of 20% to 40%, for narrow bandwidth voice signals.
Today they are typically used only in in-ear headphones and hearing aids, where their high efficiency and diminutive size is a major advantage.[20] They generally are limited at the extremes of the hearing spectrum (e.g. below 20 Hz and above 16 kHz) and require a better seal than other types of drivers to deliver their full potential. Higher-end models may employ multiple armature drivers, dividing the frequency ranges between them using a passive crossover network. A few combine an armature driver with a small moving-coil driver for increased bass output.
The thermoacoustic effect generates sound from the audio frequency Joule heating of the conductor, an effect that is not magnetic and does not vibrate the speaker. In 2013 a carbon nanotube thin-yarn earphone based on the thermoacoustic mechanism was demonstrated by a research group in Tsinghua University.[22] The as-produced CNT thin yarn earphone has a working element called CNT thin yarn thermoacoustic chip. Such a chip is composed of a layer of CNT thin yarn array supported by the silicon wafer, and periodic grooves with certain depth are made on the wafer by micro-fabrication methods to suppress the heat leakage from the CNT yarn to the substrate.[citation needed]
I see, yes, but that should serve as an important lesson – the soundstage is not real in the same sense as actual tones, bass, treble, whatever. Soundstage is a perception that’s based on many factors, and here’s a challenge for you: You should be able to find some music tracks that have better soundstage on one headphone, and other tracks that will be better on the other headphone. Most of the time it will be just one way, but when a closed headphone beats an open headphone, I expect the open headphone will still show an advantage on some tracks. Your hearing perception could be tricked by simple things like a recess or emphasis in certain frequency ranges, or even phase shift when more than one driver is in the cup.
The thermoacoustic effect generates sound from the audio frequency Joule heating of the conductor, an effect that is not magnetic and does not vibrate the speaker. In 2013 a carbon nanotube thin-yarn earphone based on the thermoacoustic mechanism was demonstrated by a research group in Tsinghua University.[22] The as-produced CNT thin yarn earphone has a working element called CNT thin yarn thermoacoustic chip. Such a chip is composed of a layer of CNT thin yarn array supported by the silicon wafer, and periodic grooves with certain depth are made on the wafer by micro-fabrication methods to suppress the heat leakage from the CNT yarn to the substrate.[citation needed]
Whether you wear headphones for your daily commute, regular workouts, or just for jamming out at home, you need a good pair that’s comfortable and can make everything sound great. Headphone tech has evolved significantly, too, so some pairs can do a lot more than just play sound. It’s not tough to find a pair that can connect to your smartphone wirelessly, or one that can keep outside commotion out.
Again, back on the automobile analogy. If you’re driving in downtown Chicago after winter time, the road is full of potholes. It would be nice to be riding in a nice SUV, rather than typical sports car with a fully stiff suspension. It doesn’t matter if your sports car happen to cost three times the cost of the SUV, it’s just the wrong car for the road. Likewise headphones. A $1,000 headphone can sound very awful on the wrong music. Don’t believe me? Try listening to Linkin Park with the $1,800 Sennheiser HD800. You will wonder where that $1,800 went.
We’re totally convinced the Sony WH-1000xM3 will be the best pick for most people, but if you’re looking for some alternatives, we have you covered there, too. We identified seven other models that are more than worthy of your consideration, each with their own specific strengths, whether it’s for use during a workout — or merely to keep you from giving your credit card too much of a workout.
An electret driver functions along the same electromechanical means as an electrostatic driver. However the electret driver has a permanent charge built into it, whereas electrostatics have the charge applied to the driver by an external generator. Electret and electrostatic headphones are relatively uncommon. Original electrets were also typically cheaper and lower in technical capability and fidelity than electrostatics. Patent applications from 2009-2013 have been approved that show by using different materials, i.e. a "Fluorinated cyclic olefin electret film", Frequency response chart readings can reach 50 kHz at 100db. When these new improved electrets are combined with a traditional dome headphone driver, headphones can be produced that are recognised by the Japan Audio Society as worthy of joining the Hi Res Audio program. US patents 8,559,660 B2. 7,732,547 B2.7,879,446 B2.7,498,699 B2.
Just a few hours of burn-in today – I don’t expect much change with Tesla-quality drivers etc. The treble is recessed almost as much as the Philips M1 I had, kind-of a worst-case scenario. So I took out my most minimal non-peaky non-bright non-sibilant headphone – the B&O H6, and even though it doesn’t sound the same as the T51p because of the H6’s “light” midrange, I wanted to get a sense of how much the T51p was recessed below a very minimal treble. My Foobar2000 settings were +2 at 2.5, +4 at 3.5, +2 at 5, +4 at 7, +6 at 10, 14, and 20 khz. Normally I wouldn’t do the dip at 5 khz, but the T51p has a nasty 10 db peak around 5 khz, which makes it difficult for portable use without a customizable equalizer. Without a treble boost it sounds very boomy as well as muffled. I can understand Beyer going to a darker sound with more bass – in fact I thought it was a move in the right direction. But they need to cut that (resonant?) peak around 5 khz. I compared to several other headphones and none of those were anything like that.
These headphones pack about 16 hours of battery life, which ought to be enough for a whole day or more, but if not, there’s always the option of using an analog cable instead. An external switch lets you turn the noise cancellation on and off. Make no mistake, these might be aimed at kids, but the quality of construction, selection of materials, and color choices give them an appearance that will still appeal to your young charges long after they’ve outgrown their Disney phase (some of us still haven’t).
I’m a former Mixer and DJ and I’d highly recommend the Beyer T1 for mixing. It is not absolutely flat, but it is an all around proper Audio Technicians Headphone. For flat response, I might eyeball the HD800 but the low end might not be the best if you are often mixing tracks with solid low ends. Flat might not always be the best option ( my opinion ). If you need to mix heavy bass tracks, it is better to have a headphone that responds better to low end EQ and is generally accepted as a more well rounded headphone.

With a Lightning a USB-C headphone you plug the headphone directly into the Lightning port (on Apple devices) or USB-C port (on Android devices). A standard headphone plug is an analog connection while this creates a direct digital connection. The headphones are powered by your phone (they use only a little bit of battery power) and have an integrated DAC (digital-to-analog converter) that's usually superior to the DAC in your phone.
Restock! Check out this 60 Watt Digital Soldering Station! This 60W digital soldering station takes the guesswork out of the temperature equation. -Temperature dial allows for precise settings ranging from 302ºF to 842ºF (150ºC to 450ºC). -Digital LCD display shows actual temperature and setting. -Temperature display toggles between Fahrenheit and Celsius. -3 temperature presets for common settings: 392ºF (200ºC), 680ºF (360ºC) and 788ºF (420ºC). -Detachable iron with pencil-style tip. -Includes cradle stand. -Works with lead-free, rosin-core, lead-based or silver-bearing solder. -Be prepared for any job, and stock up on a variety of solder, including rosin-core, lead-free, silver-bearing, clear flux and more.
×