The moving coil driver, more commonly referred to as a "dynamic" driver is the most common type used in headphones. It consists of a stationary magnet element affixed to the frame of the headphone, which sets up a static magnetic field. The magnet in headphones is typically composed of ferrite or neodymium. A voice coil, a light coil of wire, is suspended in the magnetic field of the magnet, attached to a diaphragm, typically fabricated from lightweight, high-stiffness-to-mass-ratio cellulose, polymer, carbon material, paper or the like. When the varying current of an audio signal is passed through the coil, it creates a varying magnetic field that reacts against the static magnetic field, exerting a varying force on the coil causing it and the attached diaphragm to vibrate. The vibrating diaphragm pushes on the air to produce sound waves.

However, most people won’t be able to hear the difference if they’re older than 24, have some form of noise-induced hearing loss, or are in the presence of outside noise. For this reason, we recommend wireless Bluetooth headphones for those commuting, or in noisy situations. If you’re listening primarily at home at the computer—get a set of wired headphones.

Although some headphones available are wired, many more are available that are wireless, and use Bluetooth to enable your music to be heard, even if the stereo or other device is several feet or even a few rooms away. Wired headphones deliver superior sound quality to wireless and Bluetooth because there's no chance of picking up interference from other devices, which sometimes happens with wireless headphones. In addition, wired headphones have no batteries to power them, so there's no chance of interruption should the batteries wear out.


Cable dressing and length: Most stereo headphones have just one cable, usually attached to the left earpiece (sometimes called single-sided cabling). Some models -- and all earbuds -- use a Y-cable that connects to both earpieces (double-sided). The actual cable plug, meanwhile, is usually one of two designs: a straight I-plug or an angled L-plug; the latter may be useful if your portable player has a side- or bottom-mounted headphone jack.
Wireless and truly wireless: These connect to your devices using Bluetooth, so you’re never physically tethered to your smartphone, tablet, or computer. Wireless headphones don’t use a wire to connect to an audio source, but they do use a wire to connect the two earpieces together. In contrast, “truly” wireless headphones come as two separate earpieces that don’t need wires to connect to anything. Wireless headphones are incredibly affordable; truly wireless headphones can cost anywhere from $100 to $400.

Ok, it’s been a month and a lot of new experience. I’ve auditoned ATH M-50 (clamp’s too tight; they sweat my ears just from few minutes of exposure) and Senn HD 600 (the velour pad is amazingly comfortable & size is ok). So, long story short, now I can refine my search to: circumaural&non-pleather/foam pads, which brought me to Senn HD 439 (cloth) & 518 (velour).


Headphones are available with high or low impedance (typically measured at 1 kHz). Low-impedance headphones are in the range 16 to 32 ohms and high-impedance headphones are about 100-600 ohms. As the impedance of a pair of headphones increases, more voltage (at a given current) is required to drive it, and the loudness of the headphones for a given voltage decreases. In recent years, impedance of newer headphones has generally decreased to accommodate lower voltages available on battery powered CMOS-based portable electronics. This has resulted in headphones that can be more efficiently driven by battery-powered electronics. Consequently, newer amplifiers are based on designs with relatively low output impedance.
In early powered radios, the headphone was part of the vacuum tube's plate circuit and carried dangerous voltages. It was normally connected directly to the positive high voltage battery terminal, and the other battery terminal was securely grounded. The use of bare electrical connections meant that users could be shocked if they touched the bare headphone connections while adjusting an uncomfortable headset.
The SoundSport Wireless are wireless sport earbuds that are very similar to the SoundSport Free. Instead of being true wireless earbuds, however, the two SoundSport Wireless earbuds are tethered together by cable. Aside from that, the two wireless earbuds have similar audio performance and use the same Bose Connect app. The SoundSport Wireless will last longer on a single charge (as opposed to the SoundSport Free which recharge every time they go back in their case).
The SoundSport Wireless are wireless sport earbuds that are very similar to the SoundSport Free. Instead of being true wireless earbuds, however, the two SoundSport Wireless earbuds are tethered together by cable. Aside from that, the two wireless earbuds have similar audio performance and use the same Bose Connect app. The SoundSport Wireless will last longer on a single charge (as opposed to the SoundSport Free which recharge every time they go back in their case).

Passive noise isolation is essentially using the body of the earphone, either over or in the ear, as a passive earplug that simply blocks out sound. The headphone types that provide most attenuation are in-ear canal headphones and closed-back headphones, both circumaural and supra aural. Open-back and earbud headphones provide some passive noise isolation, but much less than the others. Typical closed-back headphones block 8 to 12 dB, and in-ears anywhere from 10 to 15 dB. Some models have been specifically designed for drummers to facilitate the drummer monitoring the recorded sound while reducing sound directly from the drums as much as possible. Such headphones claim to reduce ambient noise by around 25 dB.
The outer shells of in-ear headphones are made up of a variety of materials, such as plastic, aluminum, ceramic and other metal alloys. Because in-ear headphones engage the ear canal, they can be prone to sliding out, and they block out much environmental noise. Lack of sound from the environment can be a problem when sound is a necessary cue for safety or other reasons, as when walking, driving, or riding near or in vehicular traffic.[19]
In-ear headphones are like earbuds but are an upgrade to them. These headphones fit into the wearer's ear canal and stay in place with the use of foam or rubber tips. These tips are available in custom sizes so they can fit each individual wearer. When a proper fit's achieved, in-ear headphones reduce outside noise and deliver sound quality at about the same level as over-ear and on-ear headphones.
×