A planar magnetic driver consists of a relatively large membrane that contains an embedded wire pattern. This membrane is suspended between two sets of permanent, oppositely aligned, magnets. A current passed through the wires embedded in the membrane produces a magnetic field that reacts with the field of the permanent magnets to induce movement in the membrane, which produces sound.

Dirac is mainly for resonance (narrow band) taming and not suitable for normal EQ. Accudio is good. But since the L1 already has a strong bass emphasis, boosting mids or treble just makes the imbalance worse – i.e. the freq. response becomes more ragged and the sound more harsh. To get a smoother sound and better mids and treble, reduce the bass instead.


Today they are typically used only in in-ear headphones and hearing aids, where their high efficiency and diminutive size is a major advantage.[20] They generally are limited at the extremes of the hearing spectrum (e.g. below 20 Hz and above 16 kHz) and require a better seal than other types of drivers to deliver their full potential. Higher-end models may employ multiple armature drivers, dividing the frequency ranges between them using a passive crossover network. A few combine an armature driver with a small moving-coil driver for increased bass output.

The QuietComfort 20 headphones have been around for years and years; and they’re essentailly an in-ear alterative to Bose’s QuietComfort 25. They offer the same great active noise-cancellation that the company is known for, just in a traditional wired and in-ear form factor. The QuietComfort 20 can also be switched to an “Aware” (aka ambient) mode, so you can better hear the world around you.
Communication headsets are used for two-way communication and typically consist of a headphone and attached microphone. Such headsets are used in a variety of professions as aviation, military, sports, music, and many service-oriented sectors. They come in all shapes and sizes, depending on use, required noise attenuation, and fidelity of communication needed.
A balanced armature is a sound transducer design primarily intended to increase the electrical efficiency of the element by eliminating the stress on the diaphragm characteristic of many other magnetic transducer systems. As shown schematically in the first diagram, it consists of a moving magnetic armature that is pivoted so it can move in the field of the permanent magnet. When precisely centered in the magnetic field there is no net force on the armature, hence the term 'balanced.' As illustrated in the second diagram, when there is electric current through the coil, it magnetizes the armature one way or the other, causing it to rotate slightly one way or the other about the pivot thus moving the diaphragm to make sound.
The outer shells of in-ear headphones are made up of a variety of materials, such as plastic, aluminum, ceramic and other metal alloys. Because in-ear headphones engage the ear canal, they can be prone to sliding out, and they block out much environmental noise. Lack of sound from the environment can be a problem when sound is a necessary cue for safety or other reasons, as when walking, driving, or riding near or in vehicular traffic.[19]
They’re among the best-performing wireless home/studio-style headphones in our ratings, and though the price fluctuates, you can often find them for as little as $150. That’s less than half of what you’d pay for some comparable models. If you want over-ear headphones with the convenience of Bluetooth, this pair is a steal. It comes with a detachable audio cable so that you can use your headphones without draining the battery, and the ear cups fold in for easy storage and travel.
Until now, the best true-wireless earbud features like noise cancellation or hands-free access to voice assistants were something you could only have if you spent well over $200. So when Amazon introduced its Echo Buds for just $130 with onboard Bose active noise reduction, IPX4 water-resistance, hands-free Alexa access, and a customizable fit, our only question was: Do they sound good?
Historically, many headphones had relatively high impedance, often over 500 ohms so they could operate well with high-impedance tube amplifiers. In contrast, modern transistor amplifiers can have very low output impedance, enabling lower-impedance headphones. Unfortunately, this means that older audio amplifiers or stereos often produce poor-quality output on some modern, low-impedance headphones. In this case, an external headphone amplifier may be beneficial.
One thing I suggest to prospective customers for a specific headphone, if I have that headphone on hand, is for them to suggest 2 or 3 music tracks by a particular artist and composer that I can sample on that headphone, not so much for me to suggest how it sounds, but mostly to check if that headphone has any real sonic issues with that music. For example, a headphone that’s ideal for classical and acoustic music might sound too harsh with metal and industrial goth.
For older models of telephones, the headset microphone impedance is different from that of the original handset, requiring a telephone amplifier for the telephone headset. A telephone amplifier provides basic pin-alignment similar to a telephone headset adaptor, but it also offers sound amplification for the microphone as well as the loudspeakers. Most models of telephone amplifiers offer volume control for loudspeaker as well as microphone, mute function and switching between headset and handset. Telephone amplifiers are powered by batteries or AC adaptors.
In early powered radios, the headphone was part of the vacuum tube's plate circuit and carried dangerous voltages. It was normally connected directly to the positive high voltage battery terminal, and the other battery terminal was securely grounded. The use of bare electrical connections meant that users could be shocked if they touched the bare headphone connections while adjusting an uncomfortable headset.
×