Electrostatic drivers consist of a thin, electrically charged diaphragm, typically a coated PET film membrane, suspended between two perforated metal plates (electrodes). The electrical sound signal is applied to the electrodes creating an electrical field; depending on the polarity of this field, the diaphragm is drawn towards one of the plates. Air is forced through the perforations; combined with a continuously changing electrical signal driving the membrane, a sound wave is generated. Electrostatic headphones are usually more expensive than moving-coil ones, and are comparatively uncommon. In addition, a special amplifier is required to amplify the signal to deflect the membrane, which often requires electrical potentials in the range of 100 to 1000 volts.


Dale: There are so many types of amplifiers (and DAC’s with amplifiers) that there is no shortcut for studying all of the options, unless you settle for the most generic approach. Important things to consider are power – if you don’t have enough power for your headphone and the dynamics in the music, clipping will result. Sometimes the clipping is “soft” and not readily noticed, but eventually you would discover that much of the detail goes missing or gets veiled with limited dynamics. Another consideration is whether to use a DAC, which may be a separate DAC or built into the same enclosure as the amp. Most DACs will improve the sound over the DACs that are built into computers, but when a DAC is available to replace the DAC built into most cellphones and low to mid-priced music players, you can usually expect a much greater improvement.
The Earbuds 500 won’t be available until early 2020, but they might just be worth waiting for. They look to be the natural successor to the SoundSport Free, the company’s first go at truly wireless earbuds, but probably better in every way. The Earbuds 500 will likely have a longer battery life, a smaller charging case and charge via USB-C. They will be sport-focused, too, and a more affordable option to the company’s other new-age wireless earbuds, the Noise Cancelling Earbuds 700.
Pairing high sensitivity headphones with power amplifiers can produce dangerously high volumes and damage headphones. The maximum sound pressure level is a matter of preference, with some sources recommending no higher than 110 to 120 dB. In contrast, the American Occupational Safety and Health Administration recommends an average SPL of no more than 85 dB(A) to avoid long-term hearing loss, while the European Union standard EN 50332-1:2013 recommends that volumes above 85 dB(A) include a warning, with an absolute maximum volume (defined using 40–4000 Hz noise) of no more than 100 dB to avoid accidental hearing damage.[14] Using this standard, headphones with sensitivities of 90, 100 and 110 dB (SPL)/V should be driven by an amplifier capable of no more than 3.162, 1.0 and 0.3162 RMS volts at maximum volume setting, respectively to reduce the risk of hearing damage.
A good headphone should last 25 years. The first thing to replace is earpads usually, since wear affects the sound. Sometimes the cable will get a loose connection and need replaced. The drivers should be good forever, but in some rare cases a hair can work its way in and cause a buzz or rattle. If that happens it’s usually easy to remove an earpad and pull the hair etc. out.
Smaller earbud type earpieces, which plugged into the user's ear canal, were first developed for hearing aids. They became widely used with transistor radios, which commercially appeared in 1954 with the introduction of the Regency TR-1. The most popular audio device in history, the transistor radio changed listening habits, allowing people to listen to radio anywhere. The earbud uses either a moving iron driver or a piezoelectric crystal to produce sound. The 3.5 mm radio and phone connector, which is the most commonly used in portable application today, has been used at least since the Sony EFM-117J transistor radio, which was released in 1964.[9][10] Its popularity was reinforced with its use on the Walkman portable tape player in 1979.

If you want headphones for gaming or watching movies, get some that support multi-channel surround sound. Some high-end headphones include technology that simulates surround sound, so sound effects feel like they’re coming from different directions. These headphones do a surprisingly good job at replicating the home theater experience and create an immersive experience for listeners. If you’re into big-budget blockbusters or first-person shooters and don’t have the room for a full-blown surround sound system, go for the next best thing and get headphones that support multi-channel audio.
Preferences for the length of headphone cables vary for portable users, especially depending on where you prefer to wear your device: a backpack or a pants pocket necessitates a longer cable, while you'll opt for a short one when wearing a player on a neck lavalier or an armband. But a cable length at either extreme need not be a fatal flaw: extension cables can lengthen those that are too short, and cable wraps can tighten up ones that are too long.

Unlike with other codecs, AAC test signals from Android phones like the Huawei P20 Pro, LG V30, and Samsung Galaxy Note 8 all vary wildly. Though we can’t definitively say why each Android device seems to handle AAC encoding differently, the fact of the matter is that only Apple can do it well. We suspect some of the power saving features baked into the Google ecosystem’s varying hardware has consequences for audio playback. Nowhere is this more apparent than Huawei’s power-sipping P20 Pro, which seems to cut out at around 14.25kHz.
The outer shells of in-ear headphones are made up of a variety of materials, such as plastic, aluminum, ceramic and other metal alloys. Because in-ear headphones engage the ear canal, they can be prone to sliding out, and they block out much environmental noise. Lack of sound from the environment can be a problem when sound is a necessary cue for safety or other reasons, as when walking, driving, or riding near or in vehicular traffic.[19]

Binaural recordings use a different microphone technique to encode direction directly as phase, with very little amplitude difference below 2 kHz, often using a dummy head. They can produce a surprisingly lifelike spatial impression through headphones. Commercial recordings almost always use stereo recording, rather than binaural, because loudspeaker listening is more common than headphone listening.
A headset is a headphone combined with a microphone. Headsets provide the equivalent functionality of a telephone handset with hands-free operation. Among applications for headsets, besides telephone use, are aviation, theatre or television studio intercom systems, and console or PC gaming. Headsets are made with either a single-earpiece (mono) or a double-earpiece (mono to both ears or stereo). The microphone arm of headsets is either an external microphone type where the microphone is held in front of the user's mouth, or a voicetube type where the microphone is housed in the earpiece and speech reaches it by means of a hollow tube.
Dale: There are so many types of amplifiers (and DAC’s with amplifiers) that there is no shortcut for studying all of the options, unless you settle for the most generic approach. Important things to consider are power – if you don’t have enough power for your headphone and the dynamics in the music, clipping will result. Sometimes the clipping is “soft” and not readily noticed, but eventually you would discover that much of the detail goes missing or gets veiled with limited dynamics. Another consideration is whether to use a DAC, which may be a separate DAC or built into the same enclosure as the amp. Most DACs will improve the sound over the DACs that are built into computers, but when a DAC is available to replace the DAC built into most cellphones and low to mid-priced music players, you can usually expect a much greater improvement.

Total harmonic distortion: True, headphones with lower actual total harmonic distortion (THD) will sound better than those with higher THD. But the quoted THD numbers -- "less than 1 percent" -- aren't helpful in predicting sound quality. Listen to recordings of simply recorded acoustic guitar to assess the distortion of one set of headphones versus another. Some will sound appreciably cleaner than others.


With a battery that’s rated for 15 hours of continuous use, we’re seriously hoping you don’t outlast them. If you do play for super extended periods, however, you’ll be glad that the earcups can comfortably rotate, giving you the option to drop the headband around your neck and still hear all the action. The latest version of the A50 offer significant customization options through software, and if you’re using them with a PC, you can connect directly to your sound card instead of using the optical connection. On the Xbox One version, you’ll even get Dolby Atmos for Headphones compatibility.


Generally, headphones are able to reproduce richer low-end audio, since they have larger drivers than earphones and they don't rely on an in-ear seal to deliver sound. Some listeners also find headphones more comfortable to wear, and easier to put on and take off, than they do earphones. This naturally means that headphones are bulkier, and less suited to the gym.
We are excited to announce that we are moving! To better serve our customers we will be moving from our current location on Morganton Blvd to Harper Ave across from McDonald’s in Lenoir (the old Music Center Location). We have closed our location on Morganton Blvd and will reopen at our Harper Ave. location on Wednesday. Due to the move, we may not be able to answer the store phone. For any questions, please message us here on Facebook or email us at [email protected] We can’t wait for you all to see the new RadioShack of Lenoir!
×