Sports headphones are among the most popular types of headphones and the best ones are now wireless. Sweat-resistant or even totally waterproof, they can be used at the gym or for running or biking. Some are have an open or semi-open design to let some sound in for safety reasons (so you can hear traffic noise). However, other models have a sealed, noise-isolating design.
The problem is made even worse by the fact that Android phones can’t handle AAC in a method that approaches Apple’s performance with the codec. Consequently, we will no longer be recommending AAC-only headsets here at SoundGuys, as the experience is that broken from source to source. The results are crappier and noisier than the other codecs by a longshot.

The impedance of headphones is of concern because of the output limitations of amplifiers. A modern pair of headphones is driven by an amplifier, with lower impedance headphones presenting a larger load. Amplifiers are not ideal; they also have some output impedance that limits the amount of power they can provide. To ensure an even frequency response, adequate damping factor, and undistorted sound, an amplifier should have an output impedance less than 1/8 that of the headphones it is driving (and ideally, as low as possible). If output impedance is large compared to the impedance of the headphones, significantly higher distortion is present.[11] Therefore, lower impedance headphones tend to be louder and more efficient, but also demand a more capable amplifier. Higher impedance headphones are more tolerant of amplifier limitations, but produce less volume for a given output level.
The thermoacoustic effect generates sound from the audio frequency Joule heating of the conductor, an effect that is not magnetic and does not vibrate the speaker. In 2013 a carbon nanotube thin-yarn earphone based on the thermoacoustic mechanism was demonstrated by a research group in Tsinghua University.[22] The as-produced CNT thin yarn earphone has a working element called CNT thin yarn thermoacoustic chip. Such a chip is composed of a layer of CNT thin yarn array supported by the silicon wafer, and periodic grooves with certain depth are made on the wafer by micro-fabrication methods to suppress the heat leakage from the CNT yarn to the substrate.[citation needed]
Headphones are available with high or low impedance (typically measured at 1 kHz). Low-impedance headphones are in the range 16 to 32 ohms and high-impedance headphones are about 100-600 ohms. As the impedance of a pair of headphones increases, more voltage (at a given current) is required to drive it, and the loudness of the headphones for a given voltage decreases. In recent years, impedance of newer headphones has generally decreased to accommodate lower voltages available on battery powered CMOS-based portable electronics. This has resulted in headphones that can be more efficiently driven by battery-powered electronics. Consequently, newer amplifiers are based on designs with relatively low output impedance.
Mid-range: Many headphones that cost between $50 and $130 include improved sound and useful smartphone integration (like custom EQ controls). In this price range, you’ll also see a big jump in the quality of materials used, which improves both the sound and the luxury of each pair. If you need a pair of well-made headphones with basic noise cancellation, you’ll need to spend at least this much.
Mid-range: Many headphones that cost between $50 and $130 include improved sound and useful smartphone integration (like custom EQ controls). In this price range, you’ll also see a big jump in the quality of materials used, which improves both the sound and the luxury of each pair. If you need a pair of well-made headphones with basic noise cancellation, you’ll need to spend at least this much.

Dale: The examples listed above are good general rules, but there also are so many exceptions and in-betweens that it also could be better to understand what is needed for your music, so you can narrow the search to the most appropriate headphones. For example, you may have heard that Classical music is a particular genre, but within that ‘genre’ are many very different types of music. Chamber music or pipe organ music may benefit from a headphone that’s highly detailed in the treble (a headphone that some users might say is bright), while harpsichord music and music that has a lot of strong trumpet sounds might be better served with a more rounded or softer treble.
Using headphones at a sufficiently high volume level may cause temporary or permanent hearing impairment or deafness. The headphone volume often has to compete with the background noise, especially in loud places such as subway stations, aircraft, and large crowds. Extended periods of exposure to high sound pressure levels created by headphones at high volume settings may be damaging to hearing;[25][26] Nearly 50% of teenagers and young adults (12 to 35 years old) in middle and high income countries listen to unsafe levels of sound on their personal audio devices and smartphones.[27] however, one hearing expert found in 2012 (before the worldwide adoption of smartphones as the main personal listening devices) that "fewer than 5% of users select volume levels and listen frequently enough to risk hearing loss."[28] The International Telecommunication Union recently published "Guidelines for safe listening devices/systems" recommended that sound exposure not exceed 80 decibels, A-weighted dB(A) for a maximum of 40 hours per week.[29] The European Union have also set a similar limit for users of personal listening devices (80 dB(A) for no more than 40 hours per week) and for each additional increase of 3-dB in sound exposure, the duration should be cut in half (83 dB(A) for no more than 20 hours, 86 dB(A) for 10 hours per week, 89 dB(A) for 5 hours per week and so on. Most major manufactures of smartphones now include some safety or volume limiting features and warning messaging in their devices.[30][31] though such practices have received mixed response from some segments of the buying who favor the personal choice of setting their own volume levels.

If you’re buying wireless headphones, keep a spare pair of wired headphones around in case the others run out of battery. Wireless headphones are definitely the future, and the convenience is a huge benefit, but they rely on battery power to work their magic, and batteries run out. If you’re going to be in a place where you won’t be able to recharge your wireless headphones, consider keeping a backup wired pair with you so the music never has to stop.


Smaller earbud type earpieces, which plugged into the user's ear canal, were first developed for hearing aids. They became widely used with transistor radios, which commercially appeared in 1954 with the introduction of the Regency TR-1. The most popular audio device in history, the transistor radio changed listening habits, allowing people to listen to radio anywhere. The earbud uses either a moving iron driver or a piezoelectric crystal to produce sound. The 3.5 mm radio and phone connector, which is the most commonly used in portable application today, has been used at least since the Sony EFM-117J transistor radio, which was released in 1964.[9][10] Its popularity was reinforced with its use on the Walkman portable tape player in 1979.
Be sure to assess the build quality of your prospective headphones. Some earbuds and portable devices are relatively fragile, for instance. If the headphones fold up for easy storage, are the hinges robust, or will they fall apart in a month or two? Don't forget to consider that the earpads and earbuds will get extensive wear and tear over the life of the headphones.

I have heard only the 8.35D, which are slightly dark (tilted toward the low end a little bit). But the 8.35D is very smooth and linear overall, excellent for many genres if not all. With the SRH840 you should expect a big hump in the upper bass – not ideal for monitoring. The KRK 8400 seems like the most accurate of all which is ideal for monitoring, but that’s based on a bunch of reviews, and not all of them agree 100 percent.


We were frankly surprised at just how good the AirPods Pro turned out to be. The noise cancellation is on-par with Sony’s WH-1000XM3, which is saying a lot. The new in-ear design is both comfortable and secure. And amazingly, they sound way better than Apple’s previous version. We would often bemoan the fact that the AirPods didn’t sound very good, especially when compared to the plethora of decent true wireless options for the same or less money.
Due to the extremely thin and light diaphragm membrane, often only a few micrometers thick, and the complete absence of moving metalwork, the frequency response of electrostatic headphones usually extends well above the audible limit of approximately 20 kHz. The high frequency response means that the low midband distortion level is maintained to the top of the audible frequency band, which is generally not the case with moving coil drivers. Also, the frequency response peakiness regularly seen in the high frequency region with moving coil drivers is absent. Well-designed electrostatic headphones can produce significantly better sound quality than other types.[citation needed]
Interestingly, yesterday I was comparing my beyer 770 with my AT ath30 and then I realised how important it is also the soundstage, the good separation of instruments … finally I have decided I want to take this into account as well, and not only the issue of bass, midrange and treble … Since, in my opinion lack of bass we can try to fix it, but lack of soundstage is impossible, right?
Every single Bluetooth codec has significant quality issues—despite many creative solutions employed to make the most of the limited bandwidth the standards employ. For those keeping score at home: not a single codec available can meet wired signal quality. Though Bluetooth audio has come a long way since its noisy beginnings, it’s still not ready to replace the headphone jack. Qualcomm’s aptx HD, and Sony’s LDAC 990kbps codecs come close, but everything else falls far short of the mark.

Anyway, I’m looking for comfortable headphones for casual listening from my mobile phone, and so far I’m uncomfortable with portables. I have tried many portables in multiple stores, they sweat my ears after few minutes, and their small size never cover my ears properly. Recently I have experienced one of Clarion headphone (dunno which series, its price around Rp 99.000), while its big ear cushion cover my ears properly, I felt too much pressure on the area below my ears, probably due to its weight..


The company is well known for bringing noise-canceling headphones to the general public — the QuietComfort Acoustic Noise Cancelling headphones were released in 2000 — and since then, it’s only continued to churn out industry-leading noise-canceling headphones. Its most recent iteration, the Noise Cancelling Headphones 700, might just be the best noise-canceling headphones, ever.
Active noise-cancelling headphones use a microphone, amplifier, and speaker to pick up, amplify, and play ambient noise in phase-reversed form; this to some extent cancels out unwanted noise from the environment without affecting the desired sound source, which is not picked up and reversed by the microphone. They require a power source, usually a battery, to drive their circuitry. Active noise cancelling headphones can attenuate ambient noise by 20 dB or more, but the active circuitry is mainly effective on constant sounds and at lower frequencies, rather than sharp sounds and voices. Some noise cancelling headphones are designed mainly to reduce low-frequency engine and travel noise in aircraft, trains, and automobiles, and are less effective in environments with other types of noise.

Unlike with other codecs, AAC test signals from Android phones like the Huawei P20 Pro, LG V30, and Samsung Galaxy Note 8 all vary wildly. Though we can’t definitively say why each Android device seems to handle AAC encoding differently, the fact of the matter is that only Apple can do it well. We suspect some of the power saving features baked into the Google ecosystem’s varying hardware has consequences for audio playback. Nowhere is this more apparent than Huawei’s power-sipping P20 Pro, which seems to cut out at around 14.25kHz.
Today they are typically used only in in-ear headphones and hearing aids, where their high efficiency and diminutive size is a major advantage.[20] They generally are limited at the extremes of the hearing spectrum (e.g. below 20 Hz and above 16 kHz) and require a better seal than other types of drivers to deliver their full potential. Higher-end models may employ multiple armature drivers, dividing the frequency ranges between them using a passive crossover network. A few combine an armature driver with a small moving-coil driver for increased bass output.
Noise cancellation: Noise-cancelling headphones play specific tones, much like white noise, to cancel out all of the sound around you and allow you to enjoy your music uninterrupted. Noise-cancellation is an active process, so headphones with this feature require batteries. If you’re a frequent flyer, or if you’ve got a noisy commute to work each day, you’ll love noise-cancelling headphones: they’re fantastic at keeping the cacophony of the outside world at bay.

Their combination of dual balanced-armature drivers matched with a dynamic driver to pump up the lower end are kind of engineering normally found on products that cost more than double the price of the 1Mores. Even the smaller details are very well ironed out, such as Kevlar-wrapped cables that increase resistance to wear while simultaneously reducing tangles.
A. It depends. Noise-cancelling headphones use active technology to play unique frequencies that block outside noises, and depending on which model you buy, the battery can last anywhere from 15 to 40 hours. If you’re using a set of wireless headphones, the battery will be used for both noise cancellation and wireless connectivity, so expect the battery to deplete faster if you’re using both.
64 audio A&K AAW ALO Audio Astell Astell & Kern Astell 'n Kern AstellKern astellnkern Audez'e Audioquest Audio Technica Beyerdynamic Burson canjam Cayin Chord Chord Electronics CypherLabs Earsonics Effect Audio Empire Ears Fiio Flare Audio giveaway Grado Hifiman Ibasso JH Audio Jomo Jomo Audio Meze Noble Audio Nuforce picture Sunday Picture Wednesday plusSound Review Sennheiser Sony STAX The Fav album of Ultimate Ears Watch it Wednesday Wayback Wednesday
One thing I suggest to prospective customers for a specific headphone, if I have that headphone on hand, is for them to suggest 2 or 3 music tracks by a particular artist and composer that I can sample on that headphone, not so much for me to suggest how it sounds, but mostly to check if that headphone has any real sonic issues with that music. For example, a headphone that’s ideal for classical and acoustic music might sound too harsh with metal and industrial goth.
Headphones can prevent other people from hearing the sound, either for privacy or to prevent disturbing others, as in listening in a public library. They can also provide a level of sound fidelity greater than loudspeakers of similar cost. Part of their ability to do so comes from the lack of any need to perform room correction treatments with headphones. High-quality headphones can have an extremely flat low-frequency response down to 20 Hz within 3 dB. While a loudspeaker must use a relatively large (often 15" or 18") speaker driver to reproduce low frequencies, headphones can accurately reproduce bass and sub-bass frequencies with speaker drivers only 40-50 millimeters wide (or much smaller, as is the case with in-ear monitor headphones). Headphones' impressive low-frequency performance is possible because they are so much closer to the ear that they only need to move relatively small volumes of air.
Dale: The examples listed here are good general rules, but one thing to keep in mind is in the mid-to-lower price tiers, open-back headphones aren’t nearly as common as the closed types. The smaller list of choices, and the more limited reviews of those items, could make getting a perfect fit more difficult. Sound stage and openness are often given as the advantage of the open-back types, but it’s just a general rule and some closed-back headphones excel at those properties. An important thing to consider is the music itself, since sound stage and perspective varies widely in different recordings.

The Soundsport Free, released in the fall of 2017, are Bose’s first truly wireless earbuds. They utilize the same StayHear+ Sport tips as the company’s other in-ear headphones, making them naturally more sweat-resistant and more secure than AirPods. They work with the Bose Connect app, which is pretty basic but does have a “Find My Buds” feature that, when enabled, can help you find your earbuds should you misplace them.

Frequency response: Frequency-response specifications in full-size loudspeakers are generally pretty useless in predicting sound quality, but headphone frequency-response numbers are even worse. Manufacturers have routinely exaggerated frequency-response figures to the point that they're irrelevant. Even the flimsiest, cheap headphones routinely boast extremely low bass-response performance --15Hz or 20Hz -- but almost always sound lightweight and bright. Generally, bass buffs will be happier sticking with larger 'phones.
The tech-speak description for this type of headphone is "circumaural," which includes any headphones with earcups that fully enclose your ears. Because of their size and their acoustic isolation, full-size headphones are often considered to be better-suited to home use rather than as a portable option, but the recent popularity of full-size, noise-canceling Beats headphones are challenging the rule.
A planar magnetic driver consists of a relatively large membrane that contains an embedded wire pattern. This membrane is suspended between two sets of permanent, oppositely aligned, magnets. A current passed through the wires embedded in the membrane produces a magnetic field that reacts with the field of the permanent magnets to induce movement in the membrane, which produces sound.
Preferences for the length of headphone cables vary for portable users, especially depending on where you prefer to wear your device: a backpack or a pants pocket necessitates a longer cable, while you'll opt for a short one when wearing a player on a neck lavalier or an armband. But a cable length at either extreme need not be a fatal flaw: extension cables can lengthen those that are too short, and cable wraps can tighten up ones that are too long.

If you just want to block out sound without active noise cancellation, good over-ear headphones will naturally do that to some extent. This is called noise isolation, and it simply works from the earcups forming a good seal over your ears to prevent outside noise from getting in. It's not as effective, but it's less expensive than active noise cancellation and doesn't require power.


Gaming headsets are headphones that have a microphone attached and allow users to speak to other people and hear them with the same device. In fact, gaming headsets have other practical applications as well. You can use them in business or personal situations when you want to speak to people on a computer using a video phone program or social media chat room. Although these work for music applications, they're more suited for conversational clarity.
×