To be honest, I was looking at the M50 because I knew another person that had them & was very happy with them, also I read reviews online which were positive. However, I didn’t realize until now that the possibilities are pretty endless when it comes to headphones, which is why I was asking for some direction… It just sucks cause my budget is definitely limited…
However, we also move up to high-resolution audio files, as well as a wide variety of sources, including plugging in directly to a PC or Mac, using USB DACs (digital-to-analog converters), and employing high-quality, dedicated portable players and amplifiers. Finally, we compare the headphones to some of our go-to models, both in their class and price point, as well as a level or two above to find out if they can punch above their weight.
Hi. I have more or less decided that the Philips Fidelio L1s are the ones for me. I plan to use them on my commute paired with an iPhone or the iPad as the source. I listen to a mix of pop, rock, blues and jazz so I’m not after boosting bass but I might want to fiddle with the dial on the treble and mids. Which brings me to my question. You state in your review that the L2s pair well with the Fiio e17 which lets you independently adjust treble and bass. Could the same effect be achieved lower down the $$ curve via a combination of say a Fiio E6 (for signal amplification) and a Dirac or Accudio app for equalisation?
With a Lightning a USB-C headphone you plug the headphone directly into the Lightning port (on Apple devices) or USB-C port (on Android devices). A standard headphone plug is an analog connection while this creates a direct digital connection. The headphones are powered by your phone (they use only a little bit of battery power) and have an integrated DAC (digital-to-analog converter) that's usually superior to the DAC in your phone.
Garbage in = Garbage out (GIGO) is a popular phrase used to emphasize the importance of a good source. This can be the soundcard in your laptop, the quality of your portable audio player, or the CD player you’re using for music listening. Those fall into the “Source” category. The better your source is, the better the sound will be at the headphone end. This is why we are seeing more and more audiophile digital audio players (audiophile DAPs). They are expensive but they sound good.
Wireless and truly wireless: These connect to your devices using Bluetooth, so you’re never physically tethered to your smartphone, tablet, or computer. Wireless headphones don’t use a wire to connect to an audio source, but they do use a wire to connect the two earpieces together. In contrast, “truly” wireless headphones come as two separate earpieces that don’t need wires to connect to anything. Wireless headphones are incredibly affordable; truly wireless headphones can cost anywhere from $100 to $400.
The DT770 is fine – not basshead, the COP is the same size and configuration as the 770, and both of those, large though they are, are “tighter” built so they feel less clunky than the M50. But the biggest problem for you is that the smaller headphones under $200 almost all have a steeply rolled-off treble, which is trouble for the more refined type of music. One possible exception is the Harman Soho.
Today they are typically used only in in-ear headphones and hearing aids, where their high efficiency and diminutive size is a major advantage. They generally are limited at the extremes of the hearing spectrum (e.g. below 20 Hz and above 16 kHz) and require a better seal than other types of drivers to deliver their full potential. Higher-end models may employ multiple armature drivers, dividing the frequency ranges between them using a passive crossover network. A few combine an armature driver with a small moving-coil driver for increased bass output.
The adage that you get what you pay for is generally true for audio products like headphones. What has made us big fans of the 1More brand is its ability to redefine that expectation in surprising ways. The 1More Triple Driver in-ear headphones are a great example of this: They exhibit all of the hallmarks of high-end, expensive earbuds, yet manage to keep the price highly affordable for most people.
Hearing risk from headphones' use also applies to workers who must wear electronic or communication headsets as part of their daily job (i.e., pilots, call center and dispatch operators, sound engineers, firefighters, etc.) and hearing damage depends on the exposure time. The National Institute for Occupational Safety and Health (NIOSH) recommends sound exposure not exceed 85 dB(A) over 8 hour work day as a time-weighted average. NIOSH uses the 3-dB exchange rate often referred to as "time-intensity tradeoff" which means if sound exposure level is increased by 3 decibels, the duration of exposure should be cut in half. NIOSH published several documents targeted at protecting the hearing of workers who must wear communication headsets such as call center operators, firefighters, and musicians and sound engineers.
The impedance of headphones is of concern because of the output limitations of amplifiers. A modern pair of headphones is driven by an amplifier, with lower impedance headphones presenting a larger load. Amplifiers are not ideal; they also have some output impedance that limits the amount of power they can provide. To ensure an even frequency response, adequate damping factor, and undistorted sound, an amplifier should have an output impedance less than 1/8 that of the headphones it is driving (and ideally, as low as possible). If output impedance is large compared to the impedance of the headphones, significantly higher distortion is present. Therefore, lower impedance headphones tend to be louder and more efficient, but also demand a more capable amplifier. Higher impedance headphones are more tolerant of amplifier limitations, but produce less volume for a given output level.
Over-ear and on-ear headphones effectively block out outside sounds, allowing you to hear your music or whatever else you're listening to crisply and without distraction. Over-ear headphones are sometimes known as full-size headphones because they completely envelop the wearer's ear. This results in what's known as passive noise reduction, which makes these some of the most-preferred headphones available. The only drawback is that your ears and the skin around your ears can get warm and sweaty. These are usually the heaviest type of headphones.