A good headphone should last 25 years. The first thing to replace is earpads usually, since wear affects the sound. Sometimes the cable will get a loose connection and need replaced. The drivers should be good forever, but in some rare cases a hair can work its way in and cause a buzz or rattle. If that happens it’s usually easy to remove an earpad and pull the hair etc. out.

Total harmonic distortion: True, headphones with lower actual total harmonic distortion (THD) will sound better than those with higher THD. But the quoted THD numbers -- "less than 1 percent" -- aren't helpful in predicting sound quality. Listen to recordings of simply recorded acoustic guitar to assess the distortion of one set of headphones versus another. Some will sound appreciably cleaner than others.


Active noise-cancelling headphones use a microphone, amplifier, and speaker to pick up, amplify, and play ambient noise in phase-reversed form; this to some extent cancels out unwanted noise from the environment without affecting the desired sound source, which is not picked up and reversed by the microphone. They require a power source, usually a battery, to drive their circuitry. Active noise cancelling headphones can attenuate ambient noise by 20 dB or more, but the active circuitry is mainly effective on constant sounds and at lower frequencies, rather than sharp sounds and voices. Some noise cancelling headphones are designed mainly to reduce low-frequency engine and travel noise in aircraft, trains, and automobiles, and are less effective in environments with other types of noise.
We’re totally convinced the Sony WH-1000xM3 will be the best pick for most people, but if you’re looking for some alternatives, we have you covered there, too. We identified seven other models that are more than worthy of your consideration, each with their own specific strengths, whether it’s for use during a workout — or merely to keep you from giving your credit card too much of a workout.
Dale: The examples listed above are good general rules, but there also are so many exceptions and in-betweens that it also could be better to understand what is needed for your music, so you can narrow the search to the most appropriate headphones. For example, you may have heard that Classical music is a particular genre, but within that ‘genre’ are many very different types of music. Chamber music or pipe organ music may benefit from a headphone that’s highly detailed in the treble (a headphone that some users might say is bright), while harpsichord music and music that has a lot of strong trumpet sounds might be better served with a more rounded or softer treble.
Frequency response: Frequency-response specifications in full-size loudspeakers are generally pretty useless in predicting sound quality, but headphone frequency-response numbers are even worse. Manufacturers have routinely exaggerated frequency-response figures to the point that they're irrelevant. Even the flimsiest, cheap headphones routinely boast extremely low bass-response performance --15Hz or 20Hz -- but almost always sound lightweight and bright. Generally, bass buffs will be happier sticking with larger 'phones.
Hey Mike, I’m a mixing Engineer looking to invest in a high end pair of headphones for when i’m forced to mix a song on the road. I already have the DT 770 pros and BEATS by dre headphones which i feel will be good enough for references. But I’m looking for a 3rd pair that really has a flat response and that is very detailed. I’m willing to spend $1,500 to $2,500. Are there any headphones you can recommend looking into. Thanks
The design is not mechanically stable; a slight imbalance makes the armature stick to one pole of the magnet. A fairly stiff restoring force is required to hold the armature in the 'balance' position. Although this reduces its efficiency, this design can still produce more sound from less power than any other[clarification needed]. Popularized in the 1920s as Baldwin Mica Diaphragm radio headphones, balanced armature transducers were refined during World War II for use in military sound powered telephones. Some of these achieved astonishing electro-acoustic conversion efficiencies, in the range of 20% to 40%, for narrow bandwidth voice signals.

The impedance of headphones is of concern because of the output limitations of amplifiers. A modern pair of headphones is driven by an amplifier, with lower impedance headphones presenting a larger load. Amplifiers are not ideal; they also have some output impedance that limits the amount of power they can provide. To ensure an even frequency response, adequate damping factor, and undistorted sound, an amplifier should have an output impedance less than 1/8 that of the headphones it is driving (and ideally, as low as possible). If output impedance is large compared to the impedance of the headphones, significantly higher distortion is present.[11] Therefore, lower impedance headphones tend to be louder and more efficient, but also demand a more capable amplifier. Higher impedance headphones are more tolerant of amplifier limitations, but produce less volume for a given output level.


Garbage in = Garbage out (GIGO) is a popular phrase used to emphasize the importance of a good source. This can be the soundcard in your laptop, the quality of your portable audio player, or the CD player you’re using for music listening. Those fall into the “Source” category. The better your source is, the better the sound will be at the headphone end. This is why we are seeing more and more audiophile digital audio players (audiophile DAPs). They are expensive but they sound good.
Restock! Check out this 60 Watt Digital Soldering Station! This 60W digital soldering station takes the guesswork out of the temperature equation. -Temperature dial allows for precise settings ranging from 302ºF to 842ºF (150ºC to 450ºC). -Digital LCD display shows actual temperature and setting. -Temperature display toggles between Fahrenheit and Celsius. -3 temperature presets for common settings: 392ºF (200ºC), 680ºF (360ºC) and 788ºF (420ºC). -Detachable iron with pencil-style tip. -Includes cradle stand. -Works with lead-free, rosin-core, lead-based or silver-bearing solder. -Be prepared for any job, and stock up on a variety of solder, including rosin-core, lead-free, silver-bearing, clear flux and more.
×