We were frankly surprised at just how good the AirPods Pro turned out to be. The noise cancellation is on-par with Sony’s WH-1000XM3, which is saying a lot. The new in-ear design is both comfortable and secure. And amazingly, they sound way better than Apple’s previous version. We would often bemoan the fact that the AirPods didn’t sound very good, especially when compared to the plethora of decent true wireless options for the same or less money.
Headphones are available with high or low impedance (typically measured at 1 kHz). Low-impedance headphones are in the range 16 to 32 ohms and high-impedance headphones are about 100-600 ohms. As the impedance of a pair of headphones increases, more voltage (at a given current) is required to drive it, and the loudness of the headphones for a given voltage decreases. In recent years, impedance of newer headphones has generally decreased to accommodate lower voltages available on battery powered CMOS-based portable electronics. This has resulted in headphones that can be more efficiently driven by battery-powered electronics. Consequently, newer amplifiers are based on designs with relatively low output impedance.

Dale: There are so many types of amplifiers (and DAC’s with amplifiers) that there is no shortcut for studying all of the options, unless you settle for the most generic approach. Important things to consider are power – if you don’t have enough power for your headphone and the dynamics in the music, clipping will result. Sometimes the clipping is “soft” and not readily noticed, but eventually you would discover that much of the detail goes missing or gets veiled with limited dynamics. Another consideration is whether to use a DAC, which may be a separate DAC or built into the same enclosure as the amp. Most DACs will improve the sound over the DACs that are built into computers, but when a DAC is available to replace the DAC built into most cellphones and low to mid-priced music players, you can usually expect a much greater improvement.
If you’ve been on an airplane in the last few years, you’ve probably seen the Bose QuietComfort noise-cancelling headphones before: they’re a favorite of regular travelers because they’re so good at keeping outside noise out. They’re comfortable, they sound incredible, and the noise cancellation is so impressive that you feel like you’re in your own personal bubble. These headphones are not cheap, but they’re definitely worth the money.

Digital assistant compatibility: These days, it’s kind of a rite of passage for any tech gear to be compatible with voice-controlled digital assistants, and headphones are no exception. Certain high-end headphones include a microphone that you can use with voice commands to conjure up your favorite digital assistant, but you’ll need to make sure your smartphone is compatible. For example, if you own a Samsung Galaxy S8 phone (or newer version), you can use certain headphones to execute specific voice commands on your phone, such as “Check weather.”

Unlike with other codecs, AAC test signals from Android phones like the Huawei P20 Pro, LG V30, and Samsung Galaxy Note 8 all vary wildly. Though we can’t definitively say why each Android device seems to handle AAC encoding differently, the fact of the matter is that only Apple can do it well. We suspect some of the power saving features baked into the Google ecosystem’s varying hardware has consequences for audio playback. Nowhere is this more apparent than Huawei’s power-sipping P20 Pro, which seems to cut out at around 14.25kHz.


This type combines advantages of earbuds and in-ear headphones – depending on the environment and requirements of the user, they provide passive noise reduction for quality mode (conversation or active music listening) or they give control over the sound environment around user in comfort mode (stand by or background voice/music listening).[citation needed]
However, we also move up to high-resolution audio files, as well as a wide variety of sources, including plugging in directly to a PC or Mac, using USB DACs (digital-to-analog converters), and employing high-quality, dedicated portable players and amplifiers. Finally, we compare the headphones to some of our go-to models, both in their class and price point, as well as a level or two above to find out if they can punch above their weight.
Marketed claims such as 'frequency response 4 Hz to 20 kHz' are usually overstatements; the product's response at frequencies lower than 20 Hz is typically very small.[23] Headphones are also useful for video games that use 3D positional audio processing algorithms, as they allow players to better judge the position of an off-screen sound source (such as the footsteps of an opponent or their gunfire).
Pairing high sensitivity headphones with power amplifiers can produce dangerously high volumes and damage headphones. The maximum sound pressure level is a matter of preference, with some sources recommending no higher than 110 to 120 dB. In contrast, the American Occupational Safety and Health Administration recommends an average SPL of no more than 85 dB(A) to avoid long-term hearing loss, while the European Union standard EN 50332-1:2013 recommends that volumes above 85 dB(A) include a warning, with an absolute maximum volume (defined using 40–4000 Hz noise) of no more than 100 dB to avoid accidental hearing damage.[14] Using this standard, headphones with sensitivities of 90, 100 and 110 dB (SPL)/V should be driven by an amplifier capable of no more than 3.162, 1.0 and 0.3162 RMS volts at maximum volume setting, respectively to reduce the risk of hearing damage.
hi? i want to ask a question. Im a complete newbie on the audiphilic side so i red on a site that the more the impedance is higher a headphone amp is requierd and less the impedance a headphone amp is not that much requierd cause the headphones with less impedance are made for portable players. Now let me get to the point im using cheap headphones the philips sbc hp250 they are old about 5 years and sound ok but i want to replace them so i use them mostly for listening to hours of music and i am also a musician so would it make a diference if i would buy a behringer headphone amp http://www.amazon.com/Behringer-HA400-4-Channel-Stereo-Headphone/dp/B000KIPT30/ref=sr_1_6?ie=UTF8&qid=1379715994&sr=8-6&keywords=behringer+amplifier and amplify those headphones would they play better cause now im having them plugged on a intergrated via vinyl soundcard http://www.via.com.tw/en/products/audio/codecs/vt1708s/. and they sound shitty on full volume. I am considering to buy new full size headphones and im willing to give max 80 euros for them so for the start i just want them to be loud but i want a clear sound at high volume levels. To be more specific i want a clear sound that is balanced in the lows mids and highs but not distorted and the lows should not be too much overpowered. I was sniffing around your site and found some sennheiser hd 202 ii they are not even close to 80 euros but i heard they sound great would they be better than these philips headphones and what other alternatives would you suggest me for max 80 euros
Once you’ve got that all order, to put a cherry on top it would be ideal for the amp to play nice with my laptops (PC at work, Mac at home) *and* my *iPhone* 4S.  I haven’t found a headunit that works with PCs and iDevices.  If one doesn’t exist it would be a big plus for the amp to include inputs so I can get digital sound out of my iPhone (with the Pure i20 or its ilk) and into my headphones.

Transducer technologies employed much less commonly for headphones include the Heil Air Motion Transformer (AMT); Piezoelectric film; Ribbon planar magnetic; Magnetostriction and Plasma-ionisation. The first Heil AMT headphone was marketed by ESS Laboratories and was essentially an ESS AMT tweeter from one of the company's speakers being driven at full range. Since the turn of the century, only Precide of Switzerland have manufactured an AMT headphone. Piezoelectric film headphones were first developed by Pioneer, their two models used a flat sheet of film that limited the maximum volume of air movement. Currently, TakeT produces a piezoelectric film headphone shaped similarly to an AMT transducer but, which like the Precide driver, has a variation in the size of transducer folds over the diaphragm. It additionally incorporates a two way design by its inclusion of a dedicated tweeter/supertweeter panel. The folded shape of a diaphragm allows a transducer with a larger surface area to fit within smaller space constraints. This increases the total volume of air that can be moved on each excursion of the transducer given that radiating area.

I’ve had only a few minutes one day with a 598, so I can’t say exactly. But since the HP100 is closed and the 598 is open, I would get the 598, as long as open back is OK for you. I don’t think you can go wrong with the 598 in any case – it’s a very good headphone. Watch carefully for any cracks to develop though, since there were many reports of that.


However, we also move up to high-resolution audio files, as well as a wide variety of sources, including plugging in directly to a PC or Mac, using USB DACs (digital-to-analog converters), and employing high-quality, dedicated portable players and amplifiers. Finally, we compare the headphones to some of our go-to models, both in their class and price point, as well as a level or two above to find out if they can punch above their weight.

If you have a bass problem you could find a filter of some kind that cuts the low bass. Some bass controls can do that. I haven’t found a music genre that totally lacks strong bass, although “acoustic” sometimes doesn’t have strong bass. Mainly, you should make sure your system is matched properly with amp and headphone, so the different frequencies are in balance. Then you will have better luck with different music.
Supra-aural headphones or on-ear headphones have pads that press against the ears, rather than around them. They were commonly bundled with personal stereos during the 1980s. This type of headphone generally tends to be smaller and lighter than circumaural headphones, resulting in less attenuation of outside noise. Supra-aural headphones can also lead to discomfort due to the pressure on the ear as compared to circumaural headphones that sit around the ear. Comfort may vary due to the earcup material.
If you’ve been on an airplane in the last few years, you’ve probably seen the Bose QuietComfort noise-cancelling headphones before: they’re a favorite of regular travelers because they’re so good at keeping outside noise out. They’re comfortable, they sound incredible, and the noise cancellation is so impressive that you feel like you’re in your own personal bubble. These headphones are not cheap, but they’re definitely worth the money.
Transducer technologies employed much less commonly for headphones include the Heil Air Motion Transformer (AMT); Piezoelectric film; Ribbon planar magnetic; Magnetostriction and Plasma-ionisation. The first Heil AMT headphone was marketed by ESS Laboratories and was essentially an ESS AMT tweeter from one of the company's speakers being driven at full range. Since the turn of the century, only Precide of Switzerland have manufactured an AMT headphone. Piezoelectric film headphones were first developed by Pioneer, their two models used a flat sheet of film that limited the maximum volume of air movement. Currently, TakeT produces a piezoelectric film headphone shaped similarly to an AMT transducer but, which like the Precide driver, has a variation in the size of transducer folds over the diaphragm. It additionally incorporates a two way design by its inclusion of a dedicated tweeter/supertweeter panel. The folded shape of a diaphragm allows a transducer with a larger surface area to fit within smaller space constraints. This increases the total volume of air that can be moved on each excursion of the transducer given that radiating area.

The SoundSport Wireless are wireless sport earbuds that are very similar to the SoundSport Free. Instead of being true wireless earbuds, however, the two SoundSport Wireless earbuds are tethered together by cable. Aside from that, the two wireless earbuds have similar audio performance and use the same Bose Connect app. The SoundSport Wireless will last longer on a single charge (as opposed to the SoundSport Free which recharge every time they go back in their case).
I have heard only the 8.35D, which are slightly dark (tilted toward the low end a little bit). But the 8.35D is very smooth and linear overall, excellent for many genres if not all. With the SRH840 you should expect a big hump in the upper bass – not ideal for monitoring. The KRK 8400 seems like the most accurate of all which is ideal for monitoring, but that’s based on a bunch of reviews, and not all of them agree 100 percent.
The DT770 is fine – not basshead, the COP is the same size and configuration as the 770, and both of those, large though they are, are “tighter” built so they feel less clunky than the M50. But the biggest problem for you is that the smaller headphones under $200 almost all have a steeply rolled-off treble, which is trouble for the more refined type of music. One possible exception is the Harman Soho.
AAC has some advantages when it comes to latency, but we recommend avoiding this if you care about audio quality. We found high levels of noise and lower than average frequency cutoffs—both unacceptable to audiophiles and younger listeners. Though the sound isn’t as bad as some may make it out to be, the shortcomings are noticeable to the human ear at normal listening volumes.

The design is not mechanically stable; a slight imbalance makes the armature stick to one pole of the magnet. A fairly stiff restoring force is required to hold the armature in the 'balance' position. Although this reduces its efficiency, this design can still produce more sound from less power than any other[clarification needed]. Popularized in the 1920s as Baldwin Mica Diaphragm radio headphones, balanced armature transducers were refined during World War II for use in military sound powered telephones. Some of these achieved astonishing electro-acoustic conversion efficiencies, in the range of 20% to 40%, for narrow bandwidth voice signals.
PCMag, PCMag.com and PC Magazine are among the federally registered trademarks of Ziff Davis, LLC and may not be used by third parties without explicit permission. The display of third-party trademarks and trade names on this site does not necessarily indicate any affiliation or the endorsement of PCMag. If you click an affiliate link and buy a product or service, we may be paid a fee by that merchant.

The Sony noise-cancelling headphones are a tiny miracle. They’re great at blocking the outside world, so you’ll hear your music and nothing else – at a price point that’s less than $50. Wired headphones can be a tough sell for those who’ve grown accustomed to wire-free listening, but if you’re all right with a wired connection, this pair is an easy choice.
Wired headphones are attached to an audio source by a cable. The most common connectors are 6.35 mm (¼″) and 3.5 mm phone connectors. The larger 6.35 mm connector is more common on fixed location home or professional equipment. The 3.5 mm connector remains the most widely used connector for portable application today. Adapters are available for converting between 6.35 mm and 3.5 mm devices.
×