Alternatively, online calculators can be used.[13] Once the sensitivity per volt is known, the maximum volume for a pair of headphones can be easily calculated from the maximum amplifier output voltage. For example, for a headphone with a sensitivity of 100 dB (SPL)/V, an amplifier with an output of 1 root mean square (RMS) voltage produces a maximum volume of 100 dB.

Of the tested codecs we met, aptX and aptX HD fared the best out of all our candidates. While that may seem strange to say, on the whole their results were right where they needed to be in order to stand in for a wire for commuters, and listeners over 40. You’d really only run into issues at high volumes (90+dB), so while aptX isn’t quite able to keep up with CD quality, aptX HD is able to get extremely close to the mark with a little processing creativeness. Both codecs fall short in the highest frequencies a human could potentially hear, but the vast majority of people can’t hear sounds over 18kHz anyway.
The impedance of headphones is of concern because of the output limitations of amplifiers. A modern pair of headphones is driven by an amplifier, with lower impedance headphones presenting a larger load. Amplifiers are not ideal; they also have some output impedance that limits the amount of power they can provide. To ensure an even frequency response, adequate damping factor, and undistorted sound, an amplifier should have an output impedance less than 1/8 that of the headphones it is driving (and ideally, as low as possible). If output impedance is large compared to the impedance of the headphones, significantly higher distortion is present.[11] Therefore, lower impedance headphones tend to be louder and more efficient, but also demand a more capable amplifier. Higher impedance headphones are more tolerant of amplifier limitations, but produce less volume for a given output level.

A. It depends. Noise-cancelling headphones use active technology to play unique frequencies that block outside noises, and depending on which model you buy, the battery can last anywhere from 15 to 40 hours. If you’re using a set of wireless headphones, the battery will be used for both noise cancellation and wireless connectivity, so expect the battery to deplete faster if you’re using both.

One thing I suggest to prospective customers for a specific headphone, if I have that headphone on hand, is for them to suggest 2 or 3 music tracks by a particular artist and composer that I can sample on that headphone, not so much for me to suggest how it sounds, but mostly to check if that headphone has any real sonic issues with that music. For example, a headphone that’s ideal for classical and acoustic music might sound too harsh with metal and industrial goth.
If you have a bass problem you could find a filter of some kind that cuts the low bass. Some bass controls can do that. I haven’t found a music genre that totally lacks strong bass, although “acoustic” sometimes doesn’t have strong bass. Mainly, you should make sure your system is matched properly with amp and headphone, so the different frequencies are in balance. Then you will have better luck with different music.

Ok, it’s been a month and a lot of new experience. I’ve auditoned ATH M-50 (clamp’s too tight; they sweat my ears just from few minutes of exposure) and Senn HD 600 (the velour pad is amazingly comfortable & size is ok). So, long story short, now I can refine my search to: circumaural&non-pleather/foam pads, which brought me to Senn HD 439 (cloth) & 518 (velour).
Historically, many headphones had relatively high impedance, often over 500 ohms so they could operate well with high-impedance tube amplifiers. In contrast, modern transistor amplifiers can have very low output impedance, enabling lower-impedance headphones. Unfortunately, this means that older audio amplifiers or stereos often produce poor-quality output on some modern, low-impedance headphones. In this case, an external headphone amplifier may be beneficial.
Semi-open headphones, have a design that can be considered as a compromise between open-back headphones and closed-back headphones. Some[who?] believe the term "semi-open" is purely there for marketing purposes. There is no exact definition for the term semi-open headphone. Where the open-back approach has hardly any measure to block sound at the outer side of the diaphragm and the closed-back approach really has a closed chamber at the outer side of the diaphragm, a semi-open headphone can have a chamber to partially block sound while letting some sound through via openings or vents.
Although some headphones available are wired, many more are available that are wireless, and use Bluetooth to enable your music to be heard, even if the stereo or other device is several feet or even a few rooms away. Wired headphones deliver superior sound quality to wireless and Bluetooth because there's no chance of picking up interference from other devices, which sometimes happens with wireless headphones. In addition, wired headphones have no batteries to power them, so there's no chance of interruption should the batteries wear out.
×