Although some headphones available are wired, many more are available that are wireless, and use Bluetooth to enable your music to be heard, even if the stereo or other device is several feet or even a few rooms away. Wired headphones deliver superior sound quality to wireless and Bluetooth because there's no chance of picking up interference from other devices, which sometimes happens with wireless headphones. In addition, wired headphones have no batteries to power them, so there's no chance of interruption should the batteries wear out.
A. It can be difficult, so buy earbuds that include silicone tips in multiple sizes. Everyone’s ears are unique, so most earbud manufactures include small, medium, and large silicone tips that you can easily swap out. If you want a particularly snug fit, consider getting third-party earphone tips made of memory foam, which will always adjust to the contours of your ears.

While the data signal containing Bluetooth audio is compressed, headphone and earphone manufacturers have found ways to enhance the signal to compensate for its deficiencies in a way that even audiophiles can appreciate. We've included some wireless options here, but if you're really keen on cutting the cord, check out The Best Wireless Headphones. And if you want to go completely wireless (with no cord at all connecting the two earpieces), check out The Best True Wireless Headphones—just keep in mind these are about as far from over-ear headphones as you can get.
Historically, many headphones had relatively high impedance, often over 500 ohms so they could operate well with high-impedance tube amplifiers. In contrast, modern transistor amplifiers can have very low output impedance, enabling lower-impedance headphones. Unfortunately, this means that older audio amplifiers or stereos often produce poor-quality output on some modern, low-impedance headphones. In this case, an external headphone amplifier may be beneficial.
We’re totally convinced the Sony WH-1000xM3 will be the best pick for most people, but if you’re looking for some alternatives, we have you covered there, too. We identified seven other models that are more than worthy of your consideration, each with their own specific strengths, whether it’s for use during a workout — or merely to keep you from giving your credit card too much of a workout.
I have heard only the 8.35D, which are slightly dark (tilted toward the low end a little bit). But the 8.35D is very smooth and linear overall, excellent for many genres if not all. With the SRH840 you should expect a big hump in the upper bass – not ideal for monitoring. The KRK 8400 seems like the most accurate of all which is ideal for monitoring, but that’s based on a bunch of reviews, and not all of them agree 100 percent.

There are many good articles here on Headfonia. You could click on Buyers’ Guides and read through those, then click on the Headphones topic header for each individual report. The “process” you go through is learning your own sound preferences, then matching that to the products that are available. It is a process, so you have to learn the major differences. Any shortcuts you take might be OK, but when you buy something that you discover you don’t like, make sure you can return that item.
Digital assistant compatibility: These days, it’s kind of a rite of passage for any tech gear to be compatible with voice-controlled digital assistants, and headphones are no exception. Certain high-end headphones include a microphone that you can use with voice commands to conjure up your favorite digital assistant, but you’ll need to make sure your smartphone is compatible. For example, if you own a Samsung Galaxy S8 phone (or newer version), you can use certain headphones to execute specific voice commands on your phone, such as “Check weather.”
hi? i want to ask a question. Im a complete newbie on the audiphilic side so i red on a site that the more the impedance is higher a headphone amp is requierd and less the impedance a headphone amp is not that much requierd cause the headphones with less impedance are made for portable players. Now let me get to the point im using cheap headphones the philips sbc hp250 they are old about 5 years and sound ok but i want to replace them so i use them mostly for listening to hours of music and i am also a musician so would it make a diference if i would buy a behringer headphone amp http://www.amazon.com/Behringer-HA400-4-Channel-Stereo-Headphone/dp/B000KIPT30/ref=sr_1_6?ie=UTF8&qid=1379715994&sr=8-6&keywords=behringer+amplifier and amplify those headphones would they play better cause now im having them plugged on a intergrated via vinyl soundcard http://www.via.com.tw/en/products/audio/codecs/vt1708s/. and they sound shitty on full volume. I am considering to buy new full size headphones and im willing to give max 80 euros for them so for the start i just want them to be loud but i want a clear sound at high volume levels. To be more specific i want a clear sound that is balanced in the lows mids and highs but not distorted and the lows should not be too much overpowered. I was sniffing around your site and found some sennheiser hd 202 ii they are not even close to 80 euros but i heard they sound great would they be better than these philips headphones and what other alternatives would you suggest me for max 80 euros
The thermoacoustic effect generates sound from the audio frequency Joule heating of the conductor, an effect that is not magnetic and does not vibrate the speaker. In 2013 a carbon nanotube thin-yarn earphone based on the thermoacoustic mechanism was demonstrated by a research group in Tsinghua University.[22] The as-produced CNT thin yarn earphone has a working element called CNT thin yarn thermoacoustic chip. Such a chip is composed of a layer of CNT thin yarn array supported by the silicon wafer, and periodic grooves with certain depth are made on the wafer by micro-fabrication methods to suppress the heat leakage from the CNT yarn to the substrate.[citation needed]

Earphones are very small headphones that are fitted directly in the outer ear, facing but not inserted in the ear canal. Earphones are portable and convenient, but many people consider them uncomfortable.[16] They provide hardly any acoustic isolation and leave room for ambient noise to seep in; users may turn up the volume dangerously high to compensate, at the risk of causing hearing loss.[16][17] On the other hand, they let the user be better aware of their surroundings. Since the early days of the transistor radio, earphones have commonly been bundled with personal music devices. They are sold at times with foam pads for comfort. (The use of the term earbuds, which has been around since at least 1984, did not hit its peak until after 2001, with the success of Apple's MP3 player.[18])
A planar magnetic driver consists of a relatively large membrane that contains an embedded wire pattern. This membrane is suspended between two sets of permanent, oppositely aligned, magnets. A current passed through the wires embedded in the membrane produces a magnetic field that reacts with the field of the permanent magnets to induce movement in the membrane, which produces sound.
The Bose QuietComfort 25 were released in 2015 and you can still buy them today. They are kind of like a wired version of the Bose QuietComfort 35. They have a slightly dated look, and boast almost as good levels of active noise-cancellation and sound quality as Bose’s QuietComfort 35. The important thing to remember is that even though these are wired headphones, they still need to be charged so you can turn on the active noise cancellation. Otherwise, they just work as normal over-ear headphones.
Inexpensive: Most casual users can find a good pair of headphones for between $20 and $50. Headphones in this price range sound great, include key features like an in-line microphone, and often support wireless Bluetooth connections. If you’re looking for a reliable set of headphones and you don’t need much more than audio, you don’t need to spend more than $50.

The adage that you get what you pay for is generally true for audio products like headphones. What has made us big fans of the 1More brand is its ability to redefine that expectation in surprising ways. The 1More Triple Driver in-ear headphones are a great example of this: They exhibit all of the hallmarks of high-end, expensive earbuds, yet manage to keep the price highly affordable for most people.
Ok, it’s been a month and a lot of new experience. I’ve auditoned ATH M-50 (clamp’s too tight; they sweat my ears just from few minutes of exposure) and Senn HD 600 (the velour pad is amazingly comfortable & size is ok). So, long story short, now I can refine my search to: circumaural&non-pleather/foam pads, which brought me to Senn HD 439 (cloth) & 518 (velour).
Sensitivity is a measure of how effectively an earpiece converts an incoming electrical signal into an audible sound. It thus indicates how loud the headphones are for a given electrical drive level. It can be measured in decibels of sound pressure level per milliwatt (dB (SPL)/mW) or decibels of sound pressure level per volt (dB (SPL) / V).[12] Unfortunately, both definitions are widely used, often interchangeably. As the output voltage (but not power) of a headphone amplifier is essentially constant for most common headphones, dB/mW is often more useful if converted into dB/V using Ohm's law:

Noise cancellation: Noise-cancelling headphones play specific tones, much like white noise, to cancel out all of the sound around you and allow you to enjoy your music uninterrupted. Noise-cancellation is an active process, so headphones with this feature require batteries. If you’re a frequent flyer, or if you’ve got a noisy commute to work each day, you’ll love noise-cancelling headphones: they’re fantastic at keeping the cacophony of the outside world at bay.
With a battery that’s rated for 15 hours of continuous use, we’re seriously hoping you don’t outlast them. If you do play for super extended periods, however, you’ll be glad that the earcups can comfortably rotate, giving you the option to drop the headband around your neck and still hear all the action. The latest version of the A50 offer significant customization options through software, and if you’re using them with a PC, you can connect directly to your sound card instead of using the optical connection. On the Xbox One version, you’ll even get Dolby Atmos for Headphones compatibility.
A balanced armature is a sound transducer design primarily intended to increase the electrical efficiency of the element by eliminating the stress on the diaphragm characteristic of many other magnetic transducer systems. As shown schematically in the first diagram, it consists of a moving magnetic armature that is pivoted so it can move in the field of the permanent magnet. When precisely centered in the magnetic field there is no net force on the armature, hence the term 'balanced.' As illustrated in the second diagram, when there is electric current through the coil, it magnetizes the armature one way or the other, causing it to rotate slightly one way or the other about the pivot thus moving the diaphragm to make sound.
Pairing high sensitivity headphones with power amplifiers can produce dangerously high volumes and damage headphones. The maximum sound pressure level is a matter of preference, with some sources recommending no higher than 110 to 120 dB. In contrast, the American Occupational Safety and Health Administration recommends an average SPL of no more than 85 dB(A) to avoid long-term hearing loss, while the European Union standard EN 50332-1:2013 recommends that volumes above 85 dB(A) include a warning, with an absolute maximum volume (defined using 40–4000 Hz noise) of no more than 100 dB to avoid accidental hearing damage.[14] Using this standard, headphones with sensitivities of 90, 100 and 110 dB (SPL)/V should be driven by an amplifier capable of no more than 3.162, 1.0 and 0.3162 RMS volts at maximum volume setting, respectively to reduce the risk of hearing damage.
Due to the extremely thin and light diaphragm membrane, often only a few micrometers thick, and the complete absence of moving metalwork, the frequency response of electrostatic headphones usually extends well above the audible limit of approximately 20 kHz. The high frequency response means that the low midband distortion level is maintained to the top of the audible frequency band, which is generally not the case with moving coil drivers. Also, the frequency response peakiness regularly seen in the high frequency region with moving coil drivers is absent. Well-designed electrostatic headphones can produce significantly better sound quality than other types.[citation needed]
Despite big promises from Bluetooth’s only Hi-res codec, the standard doesn’t really deliver at best, and it falls far short with its basic 330kbps setting. Both the 660kbps and 990kbps connections offer decent quality, but the 330kbps setting has a lot of noise—and a comparatively poor frequency response with higher-def content. You probably won’t hear it, but it definitely falls short of the marketing.
Wireless and truly wireless: These connect to your devices using Bluetooth, so you’re never physically tethered to your smartphone, tablet, or computer. Wireless headphones don’t use a wire to connect to an audio source, but they do use a wire to connect the two earpieces together. In contrast, “truly” wireless headphones come as two separate earpieces that don’t need wires to connect to anything. Wireless headphones are incredibly affordable; truly wireless headphones can cost anywhere from $100 to $400.
The problem is made even worse by the fact that Android phones can’t handle AAC in a method that approaches Apple’s performance with the codec. Consequently, we will no longer be recommending AAC-only headsets here at SoundGuys, as the experience is that broken from source to source. The results are crappier and noisier than the other codecs by a longshot.
Anyway, I’m looking for comfortable headphones for casual listening from my mobile phone, and so far I’m uncomfortable with portables. I have tried many portables in multiple stores, they sweat my ears after few minutes, and their small size never cover my ears properly. Recently I have experienced one of Clarion headphone (dunno which series, its price around Rp 99.000), while its big ear cushion cover my ears properly, I felt too much pressure on the area below my ears, probably due to its weight..
While noise-canceling headphones are what it’s best known for, Bose makes plenty of other high-quality headphones and earbuds for people who don’t want or need noise cancellation, which degrades audio quality and costs a premium. From true wireless AirPod competitors to old-school wired earbuds, to just cheaper wireless over-ear cans, Bose makes a headphone for every style and, more importantly, for every budget.
Headphones can prevent other people from hearing the sound, either for privacy or to prevent disturbing others, as in listening in a public library. They can also provide a level of sound fidelity greater than loudspeakers of similar cost. Part of their ability to do so comes from the lack of any need to perform room correction treatments with headphones. High-quality headphones can have an extremely flat low-frequency response down to 20 Hz within 3 dB. While a loudspeaker must use a relatively large (often 15" or 18") speaker driver to reproduce low frequencies, headphones can accurately reproduce bass and sub-bass frequencies with speaker drivers only 40-50 millimeters wide (or much smaller, as is the case with in-ear monitor headphones). Headphones' impressive low-frequency performance is possible because they are so much closer to the ear that they only need to move relatively small volumes of air.
Dale: The examples listed here are good general rules, but one thing to keep in mind is in the mid-to-lower price tiers, open-back headphones aren’t nearly as common as the closed types. The smaller list of choices, and the more limited reviews of those items, could make getting a perfect fit more difficult. Sound stage and openness are often given as the advantage of the open-back types, but it’s just a general rule and some closed-back headphones excel at those properties. An important thing to consider is the music itself, since sound stage and perspective varies widely in different recordings.
Released in 2017, the Bose SoundWear Companion is a different kind of wireless headset. It doesn’t have any earcups or earbuds, but instead it sits around your neck adn has speakers that shoot sound up towards your ear — it’s essentially a portable speaker that sits around your neck. It’s water-resistant, so you can technically work out while wearing it, but it’s really designed for the person who works at home. It’s comfortable enough to wear for lengthy periods of time, but it also has excellent built-in microphones and works great as a speakerphone.

The usual way of limiting sound volume on devices driving headphones is by limiting output power. This has the additional undesirable effect of being dependent of the efficiency of the headphones; a device producing the maximum allowed power may not produce adequate volume when paired with low-efficiency, high-impedance equipment, while the same amount of power can reach dangerous levels with very efficient earphones.
Wireless and truly wireless: These connect to your devices using Bluetooth, so you’re never physically tethered to your smartphone, tablet, or computer. Wireless headphones don’t use a wire to connect to an audio source, but they do use a wire to connect the two earpieces together. In contrast, “truly” wireless headphones come as two separate earpieces that don’t need wires to connect to anything. Wireless headphones are incredibly affordable; truly wireless headphones can cost anywhere from $100 to $400.
One thing I suggest to prospective customers for a specific headphone, if I have that headphone on hand, is for them to suggest 2 or 3 music tracks by a particular artist and composer that I can sample on that headphone, not so much for me to suggest how it sounds, but mostly to check if that headphone has any real sonic issues with that music. For example, a headphone that’s ideal for classical and acoustic music might sound too harsh with metal and industrial goth.
64 audio A&K AAW ALO Audio Astell Astell & Kern Astell 'n Kern AstellKern astellnkern Audez'e Audioquest Audio Technica Beyerdynamic Burson canjam Cayin Chord Chord Electronics CypherLabs Earsonics Effect Audio Empire Ears Fiio Flare Audio giveaway Grado Hifiman Ibasso JH Audio Jomo Jomo Audio Meze Noble Audio Nuforce picture Sunday Picture Wednesday plusSound Review Sennheiser Sony STAX The Fav album of Ultimate Ears Watch it Wednesday Wayback Wednesday
A. Near-field communication, better known as NFC, is a wireless connectivity protocol similar to Bluetooth. NFC uses less power than Bluetooth and is faster when pairing devices, but it only has a range of about four inches. Some headphones use NFC technology to drive the process of pairing headphones with smartphones, but because of the range, it’s not used to transmit sound. While both Android phones and iPhones include NFC chips, it’s not accessible in Apple devices, so if you want a pair of headphones with NFC, you’ll need to own an Android phone to take advantage of the faster pairing.
The Bose QuietComfort 35 II is arguably still the most comfortable pair of noise-canceling headphones you can buy. Released in the summer of 2018, you can think of the QuietComfort 35 II as simplified, less sophisticated and more affordable version of the new Headphones 700. The lack the transparency mode, superior call quality, USB-C charging port and on-ear gesture controls, but they still boast really impressive noise-canceling skills. The also have the tradional foldable design — it folds more compactly — that many travelers really like.
Released in 2017, the Bose QuietComfort 35 (Series I) are essentially the exact same headphones as the Series II. They have the same design, feel, sound quality and noise-canceling skills. The difference is that the Series I don’t have Google Assistant built-in and a dedicated button on the left ear cup to activate it. If you don’t care about talking to a virtual assistant while wearing your headphones, which allows you to play/pause music or skip tracks via a verbal command, then Series I or Series II shouldn’t matter to you. The catch is that the Series I is more difficult to find online and they aren’t usually that much cheaper than the Series II.
If you want headphones for gaming or watching movies, get some that support multi-channel surround sound. Some high-end headphones include technology that simulates surround sound, so sound effects feel like they’re coming from different directions. These headphones do a surprisingly good job at replicating the home theater experience and create an immersive experience for listeners. If you’re into big-budget blockbusters or first-person shooters and don’t have the room for a full-blown surround sound system, go for the next best thing and get headphones that support multi-channel audio.

One thing I suggest to prospective customers for a specific headphone, if I have that headphone on hand, is for them to suggest 2 or 3 music tracks by a particular artist and composer that I can sample on that headphone, not so much for me to suggest how it sounds, but mostly to check if that headphone has any real sonic issues with that music. For example, a headphone that’s ideal for classical and acoustic music might sound too harsh with metal and industrial goth.


A. It can be difficult, so buy earbuds that include silicone tips in multiple sizes. Everyone’s ears are unique, so most earbud manufactures include small, medium, and large silicone tips that you can easily swap out. If you want a particularly snug fit, consider getting third-party earphone tips made of memory foam, which will always adjust to the contours of your ears.
The iPhone will drive the headphone fine and make a very nice sound, but the amp will make a big improvement in harmonic extension and soundstage. Use the amp whenever possible. Both Headfonia and I concur that the E07k is a great amp, and probably the best thing you can get for up to twice the price. I’m familiar only with the E07k, the E17, and the E12. I think the E07k beats the E17 (and both are also USB DACs), while the E12 is just an amp, and has a darker sound but with more power for inefficient headphones. The Philips is not inefficient.

Case in point: the Koss PortaPro headphones first hit the market in 1984 and have become such a favorite with audiophiles that the company leaves the design (and the price tag) untouched. You can still pick one up for less than $50, and they come with a lifetime warranty, no receipt necessary. Check out our favorite budget headphones for more selections.
Although some headphones available are wired, many more are available that are wireless, and use Bluetooth to enable your music to be heard, even if the stereo or other device is several feet or even a few rooms away. Wired headphones deliver superior sound quality to wireless and Bluetooth because there's no chance of picking up interference from other devices, which sometimes happens with wireless headphones. In addition, wired headphones have no batteries to power them, so there's no chance of interruption should the batteries wear out.
×